LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2019 >> Altima Edition ONE >> Repair and Diagnosis >> Electrical >> Gauges >> Meter, Warning Lamp & Indicator >> Ecu Diagnosis Information >> Combination Meter >> Values On The Diagnosis Tool

Values On The Diagnosis Tool

Monitor Item

Condition

Value/Status

SPEED METER

[km/h]

Ignition switch ON

While driving

Input value of vehicle speed signal (CAN communication signal)

SPEED OUTPUT

[km/h]

Ignition switch ON

While driving

Output value of vehicle speed signal (CAN communication signal)

ODO OUTPUT

[km/h]

Ignition switch ON

--

Output value of odometer signal (CAN communication signal)

TACHO METER

[rpm]

Ignition switch ON

Engine running

Input value of engine speed signal (CAN communication signal)

FUEL METER

[L]

Ignition switch ON

--

Input value of fuel level sensor signal

W TEMP METER

[deg.C]

Ignition switch ON

--

Input value of engine coolant temperature signal (CAN communication signal)

ABS W/L

Ignition switch ON

ABS warning lamp ON

On

ABS warning lamp OFF

Off

VDC/TCS IND

Ignition switch ON

VDC OFF indicator lamp ON

On

VDC OFF indicator lamp OFF

Off

SLIP IND

Ignition switch ON

VDC warning lamp ON

On

VDC warning lamp OFF

Off

BRAKE W/L

Ignition switch ON

Brake warning lamp ON

On

Brake warning lamp OFF

Off

E-PKB warning lamp

Ignition switch ON

Electric parking brake warning lamp ON

On

Electric parking brake warning lamp OFF

Off

DOOR W/L

Ignition switch ON

During door open warning indication

On

Except during door open warning indication

Off

TRUNK/GLAS-H

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

HI-BEAM IND

Ignition switch ON

High beam indicator lamp ON

On

High beam indicator lamp OFF

Off

TURN IND

Ignition switch ON

Turn signal indicator lamp ON

On

Turn signal indicator lamp OFF

Off

FR FOG IND

Ignition switch ON

Front fog lamp indicator lamp ON

On

Front fog lamp indicator lamp OFF

Off

LIGHT IND

Ignition switch ON

Position lamp indicator lamp ON

On

Position lamp indicator lamp OFF

Off

OIL W/L

Ignition switch ON

During engine oil pressure warning lamp ON

On

Except during engine oil pressure warning lamp OFF

Off

MIL

Ignition switch ON

Malfunction indicator lamp (yellow) ON

On

Malfunction indicator lamp (yellow) OFF

Off

BA W/L

Ignition switch ON

FEB/EAPM warning lamp ON

On

FEB/EAPM warning lamp OFF

Off

4WD W/L

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

FUEL W/L

Ignition switch ON

During low fuel warning indication

On

Except during low fuel warning indication

Off

WASHER W/L

Ignition switch ON

During low washer fluid warning indication

On

Other than the above

Off

AIR PRES W/L

Ignition switch ON

Low tire pressure warning lamp ON

On

Low tire pressure warning lamp OFF

Off

KEY G/Y W/L

Ignition switch ON

During Intelligent Key system malfunction indication

On

Except during Intelligent Key system malfunction indication

Off

EPS W/L

Ignition switch ON

Power steering warning lamp ON

On

Power steering warning lamp OFF

Off

DDS W/L

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

IDOL STOP IND

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

CHAGE W/L

Ignition switch ON

Charge warning lamp ON

On

Charge warning lamp OFF

Off

ECO MODE IND

Ignition switch ON

ECO drive indicator lamp ON

On

ECO drive indicator lamp OFF

Off

LCD

Ignition switch ON

During engine start information indication

B&P

Ignition switch LOCK

During key ID warning indication

ID NG

Ignition switch LOCK

During steering lock information indication

ROTAT

Ignition switch LOCK

During P position warning indication

SFT P

Ignition switch ON

During ignition battery saver system information (after operation) indication

IGN AUTO OFF

Ignition switch LOCK

During Intelligent Key low battery warning indication

BATT

Ignition switch ON

During take away warning indication

NO KY

Ignition switch ON

During ignition battery saver system information (three minutes before operation) indication

3 min before IGN OFF

Ignition switch ON

During ACC warning indication

LK WN

Ignition switch ON

During engine start information indication

C&P

Ignition switch ON

Except during shift position P indication

P&N KY

Ignition switch LOCK

During key ID verification information indication

KY>PSW

Ignition switch LOCK

During remote engine start information indication

Remote engine start

Ignition switch ON

Other than the above

Off

ACC SET SPEED

Ignition switch ON

During set vehicle speed indicator not displayed

Off

During set vehicle speed indicator displayed

Indicates the set vehicle speed

ACC UNIT

Ignition switch ON

Set vehicle speed indicator unit display ON

On

Set vehicle speed indicator unit display OFF

Off

FUEL CAP W/L

Ignition switch ON

During fuel filler cap warning indication

On

Other than the above

Off

O/D OFF SW

Ignition switch ON

SPORT mode switch ON

On

SPORT mode switch OFF

Off

M RANGE SW

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

NM RANGE SW

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

AT SFT UP SW

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

AT SFT DWN SW

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

ST SFT UP SW

Ignition switch ON

Paddle shifter operated in up position

On

Shift selector is in non manual mode up position

Off

ST SFT DWN SW

Ignition switch ON

Paddle shifter operated in down position

On

Other than the above

Off

PKB SW

Ignition switch ON

Parking brake switch ON (except electric parking brake system)

On

Parking brake switch OFF (except electric parking brake system)

Off

BUCKLE SW

Ignition switch ON

Driver seat belt not fastened

On

Driver seat belt fastened

Off

BRAKE OIL SW

Ignition switch ON

Brake fluid level switch ON

On

Brake fluid level switch OFF

Off

ECO MODE SW

Ignition switch ON

ECO mode switch ON

On

ECO mode switch OFF

Off

CHG CONCT DET

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

LED LMP R OPEN

Ignition switch ON

Front combination lamp RH malfunction

On

Front combination lamp RH normal

Off

LED LMP L OPEN

Ignition switch ON

Front combination lamp LH malfunction

On

Front combination lamp LH normal

Off

DISTANCE

[km]

Ignition switch ON

--

Distance to empty

OUTSIDE TEMP

[deg.C]

Ignition switch ON

--

Displays the ambient air temperature which is input from the ambient sensor.

CRANKING SIG

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

On

ST CNT SIG

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

On

BUZZER

Ignition switch ON

Buzzer ON

On

Buzzer OFF

Off

BATTERY CIRCUIT STATUS

--

Shipping mode ON

On

Other than shipping mode

Off

PARKING ASSIST DSP

Ignition switch ON

Sonar display setting ON

On

Sonar display setting OFF

Off

PARKING ASSIST SENSOR

Ignition switch ON

When sonar set to "OFF"

Off

When sonar set to "Rear"

Rear

When sonar set to "Front"

FRONT

When sonar set to "ON"

On

Other than above

Not support

PARKING ASSIST VOLUME

Ignition switch ON

When sonar volume set to "HIGH"

HIGH

When sonar volume set to "MIDDLE"

MEDIUM

When sonar volume set to "LOW"

LOW

Other than above

Not support

PARKING ASSIST RANGE

Ignition switch ON

When sonar range set to "NEAR"

NEAR

When sonar range set to "MEDIUM"

MEDIUM

When sonar range set to "FAR"

FAR

Other than above

Not support

TPMS DISP

Ignition switch ON

TPMS display ON

On

TPMS display OFF

Off

SONAR SET AVA

Ignition switch ON

During the setting of the combination meter

Available

Other than the above

Unavailable

STRG SW INPUT

Ignition switch ON

BACK switch is pressed

SW1

UP switch is pressed

SW2

DOWN switch is pressed

SW3

OK switch is pressed

SW4

LEFT switch is pressed

SW5

RIGHT switch is pressed

SW6

VOL DOWN switch is pressed

SW7

VOL UP switch is pressed

SW8

TEL switch is pressed

SW9

VR switch is pressed

SW10

SEEK DOWN switch is pressed

SW11

SEEK UP switch is pressed

SW12

Other than above

NO INPUT

ITS SONAR SET OUTPUT

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

NO SW ST

ITS SONAR SET OUTPUT

Ignition switch ON

LDW status in combination meter selection ON

LDW On

LDW status in combination meter selection OFF

LDW Off

BSW status in combination meter selection ON

BSW On

BSW status in combination meter selection OFF

BSW Off

AEB status in combination meter selection ON

FEB On

AEB status in combination meter selection OFF

FEB Off

Other than above

NO SW ST

HI-BEAM ASST IND

Ignition switch ON

High beam assist indicator lamp ON

On

High beam assist indicator lamp OFF

Off

SONAR DET STATUS

Ignition switch ON

Sonar control unit detected the obstacle

On

Sonar control unit not detected the obstacle

Off

SONAR WARN

Ignition switch ON

Sonar sensor error ON (sonar system ON)

ERROR

Sonar system OFF

DEACT

Sonar sensor error OFF (sonar system ON)

Off

SONAR DET DSP RC

Ignition switch ON

Level of distance from center sensor rear to obstacle level1

LEVEL1

Level of distance from center sensor rear to obstacle level2

LEVEL2

Level of distance from center sensor rear to obstacle level3

LEVEL3

Level of distance from center sensor rear to obstacle level4

LEVEL4

SONAR DET DSP AREA RC

Ignition switch ON

Obstacle is within the warning area of center sensor rear

On

Other than above

Off

SONAR DET DSP RL

Ignition switch ON

Level of distance from corner sensor rear LH to obstacle level1

LEVEL1

Level of distance from corner sensor rear LH to obstacle level2

LEVEL2

Level of distance from corner sensor rear LH to obstacle level3

LEVEL3

Level of distance from corner sensor rear LH to obstacle level4

LEVEL4

SONAR DET DSP AREA RL

Ignition switch ON

Obstacle is within the warning area of corner sensor rear LH

On

Other than above

Off

SONAR DET DSP RR

Ignition switch ON

Level of distance from corner sensor rear RH to obstacle level1

LEVEL1

Level of distance from corner sensor rear RH to obstacle level2

LEVEL2

Level of distance from corner sensor rear RH to obstacle level3

LEVEL3

Level of distance from corner sensor rear RH to obstacle level4

LEVEL4

SONAR DET DSP AREA RR

Ignition switch ON

Obstacle is within the warning area of corner sensor rear RH

On

Other than above

Off

SONAR DET DSP FC

Ignition switch ON

Level of distance from center sensor front to obstacle level1

LEVEL1

Level of distance from center sensor front to obstacle level2

LEVEL2

Level of distance from center sensor front to obstacle level3

LEVEL3

Level of distance from center sensor front to obstacle level4

LEVEL4

SONAR DET DSP AREA FC

Ignition switch ON

Obstacle is within the warning area of center sensor front

On

Other than above

Off

SONAR DET DSP FL

Ignition switch ON

Level of distance from corner sensor front LH to obstacle level 1

LEVEL1

Level of distance from corner sensor front LH to obstacle level 2

LEVEL2

Level of distance from corner sensor front LH to obstacle level 3

LEVEL3

Level of distance from corner sensor front LH to obstacle level 4

LEVEL4

SONAR DET DSP AREA FL

Ignition switch ON

Obstacle is within the warning area of corner sensor front LH

On

Other than above

Off

SONAR DET DSP FR

Ignition switch ON

Level of distance from corner sensor front RH to obstacle level 1

LEVEL1

Level of distance from corner sensor front RH to obstacle level 2

LEVEL2

Level of distance from corner sensor front RH to obstacle level 3

LEVEL3

Level of distance from corner sensor front RH to obstacle level 4

LEVEL4

SONAR DET DSP AREA FR

Ignition switch ON

Obstacle is within the warning area of corner sensor front RH

On

Other than above

Off

SONAR DIST DSP

Ignition switch ON

Distance from obstacle to corner sensor is less than 30 cm

STOP

Distance from obstacle to corner sensor is 30 cm or more and less than 40 cm

30 cm

Distance from obstacle to corner sensor is 40 cm or more and less than 50 cm

40 cm

Distance from obstacle to corner sensor is 50 cm or more and less than 60 cm

50 cm

Distance from obstacle to corner sensor is 60 cm or more and less than 70 cm

60 cm

Distance from obstacle to corner sensor is more than 70 cm

Off

ENG SOAK TIME

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

0

FCW IND

Ignition switch ON

FCW system display ON

On

FCW system display OFF

Off

LDW IND

Ignition switch ON

LDW system display ON

On

LDW system display OFF

Off

TPMS FLT TIRE

Ignition switch ON

Flat tire

On

Other than above

Off

TPMS PRESS L

Ignition switch ON

Tire pressure is low

On

Tire pressure is normal

Off

4WD CL TMP H

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

4WD TIRE CHCK

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

4WD SYS MALF

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

ASCD SPD BLNK

Ignition switch ON

Set vehicle speed indicator blinking

On

Set vehicle speed indicator not blinking

Off

ASCD STATUS

Ignition switch ON

ASCD system OFF

Off

ASCD system ON

ASCD

ASCD set vehicle speed

CRUISE

ASCD REQ SPD

Ignition switch ON

While driving

Same value as ASCD or speed limiter set vehicle speed

E/O CHG TMNG RST

Ignition switch ON

Resetting of a remaining distance to the engine oil change time.

On

Other than above

Off

ECO DRIVE NAVI

Ignition switch ON

--

LEVEL 0 - LEVEL 30

Set Forward Emergency Brake

Ignition switch ON

AEB setting is ON

On

AEB setting is OFF

Off

AEB is not available.

Not support

SET LDW

Ignition switch ON

LDW setting is ON

On

LDW setting is OFF

Off

LDW is not available.

Not support

SET BSW

Ignition switch ON

BSW setting is ON

On

BSW setting is OFF

Off

BSW is not available.

Not support

Set BSW Brightness

Ignition switch ON

BSW brightness setting is DARK

DARK

BSW brightness setting is NORMAL

NORMAL

BSW brightness setting is BRIGHT

BRIGHT

BSW is not available.

Not support

SET LDP

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

SET BSI

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

SET IBA

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

MSS PEDAL HIGH TEMP

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

CHASSIS CONTROL WARN

Ignition switch ON

Chassis control display (warning) indication

On

Other than above

Off

MSS INFO&WARN1

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

MSS INFO&WARN2

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

MSS INFO&WARN3

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

MSS INFO&WARN4

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Not support

TIRE PRESS FR

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

0 - 63.75

TIRE PRESS FL

Ignition switch ON

--

0 - 63.75

TIRE PRESS RR

Ignition switch ON

--

0 - 63.75

TIRE PRESS RL

Ignition switch ON

--

0 - 63.75

BSW IND

Ignition switch ON

BSW system display ON

On

BSW system display OFF

Off

LDP IND

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

BSI IND

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

RAM error

Ignition switch ON

RAM error detected

GDC

Gauge

Zero

Graphic

Other than above

Normal

Status of call display

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

PP display status

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Off

PP setting status

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

Avail 2

Vehicle distance

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

0

BSI/BSW status

Ignition switch ON

BSI/BSW is ON

On

BSI/BSW is OFF

Off

BSI/BSW is not available.

No spprt

Jump request

Ignition switch ON

NOTE: This item is displayed, but cannot be monitored.

No spprt

EAPM status

Ignition switch ON

EAPM is ON

On

EAPM is OFF

Off

EAPM is not available.

No spprt