Self Diagnostic Result

When "CRNT" is displayed on self-diagnosis result

The system is presently malfunctioning.

When "PAST" is displayed on self-diagnosis result

System malfunction in the past is detected, but the system is presently normal.

Freeze Frame Data (FFD)

When DTC is detected, a vehicle status shown below is recorded and displayed on CONSULT.

Item name	Indication/Unit	Display item
IGN COUNTER	(0 - 39)	The number of times that power switch is ON after the DTC is detected is displayed. When "0" is displayed: It indicates that the system is presently malfunctioning. When except "0" is displayed: It indicates that system malfunction in the past is detected, but the system is presently normal. NOTE: Each time when power switch is turned OFF to ON, numerical number increases in 1 -> 2 -> 3...38 -> 39. When the operation number of times exceeds 39, the number do not increase and "39" is displayed until self-diagnosis is erased.
DTC COUNTER	--	Displays the number of DTCs detected upon DTC detection.
BRAKE PEDAL STATUS	Off	Displays when the brake pedal is not depressed upon DTC detection.
	On 1	Displays when the either stop lamp switch or brake pedal position switch is ON upon DTC detected.
	On 2	Displays when the both stop lamp switch and brake pedal position switch are ON upon DTC detected.
	NO SIGNAL	Displays when the operation status of the brake pedal cannot be checked upon DTC detection.
IGN SW	Off	Displays when the ignition switch is OFF upon DTC detection.
IGN SW	On	Displays when the ignition switch is ON upon DTC detection.
ENGINE STATUS	STOP	Displays when the engine is stopped upon DTC detection.
	RUN 1	Displays when the cranking status.
	RUN 2	Displays when the engine running status.
CAN DIAG PERMIS STATUS	On 1	Displays when the ignition switch is OFF upon DTC detection.
	On 2	Displays when the ignition switch is ON upon DTC detection.
	NO SIGNAL	Displays when signals cannot be received via CAN communication upon DTC detection.
LAST BRAKE OPERATING (LH)	NO REQUEST	Displays when no operation request of the rear LH brake is given upon DTC detection.
	INHIBIT	Displays when operation request of the rear LH brake is inhibited upon DTC detection.
	ACT 2	Displays when the braking of the rear LH brake is requested upon DTC detection.
	RLS 2	Displays when the releasing of the rear LH brake is requested upon DTC detection.
LAST BRAKE OPERATING (RH)	NO REQUEST	Displays when no operation request of the rear RH brake is given upon DTC detection.
	INHIBIT	Displays when operation request of the rear RH brake is inhibited upon DTC detection.
	ACT 2	Displays when the braking of the rear RH brake is requested upon DTC detection.
	RLS 2	Displays when the releasing of the rear RH brake is requested upon DTC detection.
BRAKE STATUS (LH)	ACT 1	Displays but not used
	ACT 2	Displays when the motor of the parking brake actuator LH is rotating upon DTC detection. (Braking)
	ACT 3	Displays when the motor of the parking brake actuator LH is OFF upon DTC detection. (Braking)
	RLS 1	Displays when the motor of the parking brake actuator LH is OFF after obtaining clearance of brake pad and disc rotor upon DTC detected. (Release)
	RLS 2	Displays when the motor of the parking brake actuator LH is rotating to obtain clearance of brake pad and disc rotor upon DTC detected. (Release)
	UNKNO	Displays when the operation status of the rear LH brake is unclear upon DTC detection.
	INIT	Displays when the operation status of the rear LH brake is the initial status upon DTC detection.
	RLS 3	Displays when the motor of the parking brake actuator LH is OFF after the piston is returned to the end upon DTC detection. (Release)
	RLS 4	Displayed when the motor of the parking brake actuator LH is rotating until the piston is returned to the end upon DTC detected. (Release)
BRAKE STATUS (RH)	ACT 1	Displayed but not used
	ACT 2	Displays when the motor of the parking brake actuator RH is rotating upon DTC detection. (Braking)
	ACT 3	Displays when the motor of the parking brake actuator RH is OFF upon DTC detection. (Braking)
	RLS 1	Displays when the motor of the parking brake actuator RH is OFF after obtaining clearance of brake pad and disc rotor upon DTC detected. (Release)
	RLS 2	Displays when the motor of the parking brake actuator RH is rotating to obtain clearance of brake pad and disc rotor upon DTC detected. (Release)
	UNKNO	Displays when the operation status of the rear RH brake is unclear upon DTC detection.
	INIT	Displays when the operation status of the rear RH brake is the initial status upon DTC detection.
	RLS 3	Displays when the motor of the parking brake actuator RH is OFF after the piston is returned to the end upon DTC detection. (Release)
	RLS 4	Displayed when the motor of the parking brake actuator RH is rotating until the piston is returned to the end upon DTC detected. (Release)
BATTERY VOLT	V	Display the electric parking brake control module power supply upon DTC detection.
BRAKE FORCE (LH)	KN	Displays the braking force of the rear LH brake upon DTC detection.
BRAKE FORCE (RH)	KN	Displays the braking force of the rear RH brake upon DTC detection.
SLOPE RATIO	%	Displays the inclination of road surface upon DTC detection.
STOP/START SYSTEM STATUS	Off	Displays when the stop/start system is deactivated upon DTC detection.
STOP/START SYSTEM STATUS	On	Displays when the stop/start system is activated upon DTC detection.