Symptom Table

CAUTION: Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom		Possible cause	Inspection item
Headlamp (HI) is not turned ON.	One side	Fuse Halogen bulb (HI) Harness between IPDM E/R and the headlamp high IPDM E/R	Headlamp (HI) circuit Refer to HEADLAMP (HI) CIRCUIT .
Headlamp (HI) is not turned ON.	Both sides	Symptom diagnosis "BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON" Refer to BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON .
Headlamp (HI) is not turned OFF.	When ignition switch is turned ON.
Headlamp (HI) is not turned OFF.	When ignition switch is turned OFF.	IPDM E/R	-
High beam indicator lamp is not turned ON. [The headlamp (HI) is turned ON.]		Combination meter	Combination meter Data monitor "HI-BEAM IND" BCM (HEAD LAMP) Active test "HEADLAMP"
Headlamp (LO) is not turned ON.	One side	Fuse Xenon bulb (LO) Harness between IPDM E/R and the headlamp low IPDM E/R	Headlamp (LO) circuit Refer to HEADLAMP (LO) CIRCUIT .
Headlamp (LO) is not turned ON.	Both sides	Symptom diagnosis "BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON" Refer to BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON .
Headlamp (LO) is not turned OFF.	When ignition switch is turned ON.
Headlamp (LO) is not turned OFF.	When ignition switch is turned OFF.	IPDM E/R	-
Headlamp is not turned ON/OFF with the lighting switch AUTO.		Combination switch Harness between the combination switch and BCM BCM	Combination switch Refer to SYMPTOM DIAGNOSIS
		Optical sensor Harness between the optical sensor and BCM BCM	Optical sensor Refer to OPTICAL SENSOR
Front fog lamp is not turned ON.	One side	Front fog lamp bulb Harness between IPDM E/R and the front fog lamp Front fog lamp IPDM E/R	Front fog lamp circuit Refer to FRONT FOG LAMP CIRCUIT .
Front fog lamp is not turned ON.	Both sides	Symptom diagnosis "BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON" Refer to BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON .
Front fog lamp is not turned ON.
Parking lamp is not turned ON.		Parking lamp bulb Harness between IPDM E/R and the front combination lamp Front combination lamp IPDM E/R	Parking lamp circuit Refer to PARKING LAMP CIRCUIT .
Tail lamp is not turned ON.		Tail lamp bulb Harness between IPDM E/R and the rear combination lamp Rear combination lamp	Tail lamp circuit Refer to TAIL LAMP CIRCUIT .
License plate lamp is not turned ON.		License plate lamp bulb Harness between IPDM E/R and the license plate lamp License plate lamp	License plate lamp circuit Refer to LICENSE PLATE LAMP CIRCUIT .
Tail lamp and the license plate lamp are not turned ON.		Fuse Harness between IPDM E/R and the rear combination lamp IPDM E/R	License plate lamp circuit Refer to LICENSE PLATE LAMP CIRCUIT .
Parking lamp, the tail lamp and the license plate lamp are not turned ON. Parking lamp, the tail lamp and the license plate lamp are not turned OFF. (Each illumination is turned ON/OFF.)		Symptom diagnosis "PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON" Refer to PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON .
Position lamp indicator is not turned ON. (Parking, tail lamps are turned ON.)		Combination meter	Combination meter Data monitor "LIGHT IND" BCM (HEAD LAMP) Active test "TAIL LAMP"
Turn signal lamp does not blink.	Indicator lamp is normal. (Applicable side performs the high flasher activation.)	Harness between BCM and each turn signal lamp Turn signal lamp bulb	Turn signal circuit Refer to TURN SIGNAL LAMP CIRCUIT .
Turn signal lamp does not blink.	Indicator lamp is included.	Combination switch Harness between the combination switch and BCM BCM	Combination switch Refer to COMBINATION SWITCH .
Turn signal indicator lamp does not blink. (Turn signal indicator lamp is normal.)	One side	Combination meter	-
	Both sides (Always)	Turn signal indicator lamp signal BCM Combination meter	Combination meter Data monitor "TURN IND" BCM (FLASHER) Active test "FLASHER"
	Both sides (Only when activating hazard warning lamp with the ignition switch OFF)	Combination meter power supply and the ground circuit Combination meter	Combination meter Power supply and the ground circuit Refer to POWER SUPPLY AND GROUND CIRCUIT .
Hazard warning lamp does not activate. Hazard warning lamp continues activating. (Turn signal is normal.)		Hazard switch Harness between the hazard switch and BCM BCM	Hazard switch Refer to HAZARD SWITCH .