Headlamp High Beam Does Not Illuminate (Both Sides)

With CONSULT

1. Select "BCM" on CONSULT. Select "HEAD LAMP" on "SELECT TEST ITEM" screen.
2. Select "DATA MONITOR". Make sure that "HI BEAM SW" turns ON-OFF linked with operation of combination switch (lighting and turn signal switch).

   When combination switch (lighting and turn signal switch) is high position: HI BEAM SW ON 

   Without CONSULT

   Refer to , "COMBINATION SWITCH INSPECTION ".

   OK or NG 

   OK: GO TO 2.

   NG: Check combination switch (lighting and turn signal switch). Refer to , "COMBINATION SWITCH INSPECTION ".

With CONSULT

1. Select "IPDM E/R" on CONSULT. Select "ACTIVE TEST".
2. Select "LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "HI" screen.
4. Make sure headlamp high beam operates.

   Headlamp high beam should operate (Headlamp high beam repeats ON-OFF every 2 seconds)  .

Without CONSULT

1. Start auto active test. Refer to , "AUTO ACTIVE TEST ".
2. Make sure headlamp high beam operates.

   Headlamp high beam should operate  .

   OK or NG 

   OK: GO TO 3.

   NG: GO TO  4.

1. Select "IPDM E/R" on CONSULT. Select "DATA MONITOR".
2. Make sure "HL HI REQ" turns ON when combination switch (lighting and turn signal switch) is in high position.

   When combination switch (lighting and turn signal switch) is high position: HL HI REQ ON 

   OK or NG 

   OK: Replace IPDM E/R. Refer to , "REMOVAL AND INSTALLATION OF IPDM E/R ".

   NG: Replace BCM. Refer to , "REMOVAL AND INSTALLATION OF BCM ".

Inspect 10A fuse [No. 34 (RH) and No. 35 (LH), located in the IPDM E/R].

OK or NG 

OK: GO TO 5.

NG: Repair harness.

Inspect inoperative headlamp bulbs.

OK or NG 

OK: GO TO 6.

NG: Replace headlamp bulb. Refer to , "BULB REPLACEMENT ".

With CONSULT

1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select "IPDM E/R" on CONSULT. Select "ACTIVE TEST".
5. Select "LAMPS" on "SELECT TEST ITEM" screen.
6. Touch "HI" screen.
7. When headlamp high beam is operating, check voltage between headlamp harness connector and ground (Headlamp high beam repeats ON-OFF every 2 seconds).

   Terminal				Voltage
   (+)			(-)
   Headlamp connector		Terminal
   RH	E20	6	Ground	Battery voltage
   LH	E21

Fig 1: Checking Headlamp Input Signal

Courtesy of NISSAN NORTH AMERICA, INC.

Without CONSULT

1. Turn ignition switch OFF.
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Start auto active test. Refer to , "AUTO ACTIVE TEST ".
5. When headlamp high beam is operating, check voltage between headlamp harness connector and ground.

   Terminal				Voltage
   (+)			(-)
   Headlamp connector		Terminal
   RH	E20	6	Ground	Battery voltage
   LH	E21

   OK or NG 

   OK: GO TO 7.

   NG: GO TO  8.

1. Turn ignition switch OFF.
2. Check continuity between headlamp harness connector and ground.

   Headlamp connector		Terminal	Ground	Continuity
   RH	E20	5		Yes
   LH	E21

   Fig 2: Checking Headlamp Ground Circuit

   Courtesy of NISSAN NORTH AMERICA, INC.

   OK or NG 

   OK: Check front combination lamp connector for damage or poor connection. Repair as necessary.

   NG: Repair harness.

1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector (A) and headlamp harness connector (B).

   Circuit	A		B		Continuity
   	Connector	Terminal	Connector	Terminal
   RH	E47	56	E20	6	Yes
   LH		55	E21

   Fig 3: Checking Headlamp Circuit

   Courtesy of NISSAN NORTH AMERICA, INC.

   OK or NG 

   OK: Replace IPDM E/R. Refer to , "REMOVAL AND INSTALLATION OF IPDM E/R ".

   NG: Repair harness or connector.