DTC 31-xx*, 32-xx*, 33-xx*, 34-xx*, 35-xx*, 36-xx*, 37-xx*, 38-xx*: ABS Right-front Inlet Solenoid Valve Malfunction; ABS Right-Front Outlet Solenoid Valve Malfunction; ABS Left-Front Inlet Solenoid Valve Malfunction; ABS Left-Front Outlet Solenoid Valve Malfunction; ABS Right-Rear Inlet Solenoid Valve Malfunction; ABS Right-Rear Outlet Solenoid Valve Malfunction; ABS Left-Rear Inlet Solenoid Valve Malfunction; ABS Left-Rear Outlet Solenoid Valve Malfunction
WARNING: This page is about a different car, the 2011 Honda Fit, 2010 Honda Fit, and 2009 Honda Fit. However, it is still accessible from the selected car via links, so may be relevant.
*: Any two-character sub-code (see table below)
DTC MALFUNCTION TABLE
| Subcode | Malfunction | Note (DTC) |
|---|---|---|
| 01 | Solenoid Initial Pulse | 31-01, 32-01, 33-01, 34-01, 35-01, 36-01, 37-01, 38-01 |
| 02 | Initial Feedback Signal | 31-02, 33-02, 35-02, 37-02 |
| 11 | Feedback Signal | 31-11, 33-11, 35-11, 37-11 |
| 21 | Solenoid Pulse | 31-21, 32-21, 33-21, 34-21, 35-21, 36-21, 37-21, 38-21 |
| 22 | Solenoid Speculative | 31-22, 32-22, 33-22, 34-22, 35-22, 36-22, 37-22, 38-22 |
| 23 | Solenoid Stuck ON | 31-23, 32-23, 33-23, 34-23, 35-23, 36-23, 37-23, 38-23 |
| 24 | Feedback Signal/Solenoid Stuck ON | 31-24, 33-24, 35-24, 37-24 |
NOTE:
Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information. (See General Troubleshooting Information ).
- Turn the ignition switch to ON (II).
- Clear the DTC with the HDS.
- Turn the ignition switch to LOCK (0), then turn it to ON (II) again.
- Check for DTCs with the HDS.
Is DTC 31-xx, 32-xx, 33-xx, 34-xx, 35-xx, 36-xx, 37-xx or 38-xx indicated?
YES - Go to step 5.
NO - Intermittent failure, the system is OK at this time. Refer to intermittent failures troubleshooting (see Intermittent Failures ).
- Update the VSA modulator-control unit if it does not have the latest software (see VSA MODULATOR-CONTROL UNIT UPDATE ).
- Turn the ignition switch to LOCK (0), then turn it to ON (II) again.
- Check for DTCs with the HDS.
Is DTC 31-xx, 32-xx, 33-xx, 34-xx, 35-xx, 36-xx, 37-xx or 38-xx indicated?
YES - Check for loose terminals in the VSA modulator-control unit 36P connector. If the symptom/indication is still present, replace the VSA modulator-control unit (see VSA MODULATOR-CONTROL UNIT REMOVAL AND INSTALLATION ).
NO - If the VSA modulator-control unit was updated, troubleshooting is complete. If any other DTCs are indicated, go to the indicated DTCs troubleshooting.