LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2011 >> Sentra S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (Manual Transmission - RS6F52H) >> Service Information >> Preparation >> Special Service Tool

Special Service Tool

WARNING: This page is about a different variant/trim than selected.

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

SPECIAL SERVICE TOOL REFERENCE CHART

Tool number
(Kent-Moore No.)
Tool name		 Description
KV381054S0
(J-34286)
Puller
G04875581Courtesy of NISSAN MOTOR CO., U.S.A.
  • Removing differential side bearing outer race (clutch housing side)
  • Removing differential side bearing outer race (transaxle case side)
  • Removing mainshaft front bearing
ST33400001
(J-26082)
Drift
G04875582Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side oil seal (clutch housing side)
  1. 60 mm (2.36 in) dia. 
  2. 47 mm (1.85 in) dia. 
ST35321000
(-)
Drift
G04876274Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing input shaft oil seal
  • Installing reverse main gear
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly
  • Installing 2nd main gear bushing
  • Installing 3rd main gear

  1. 49 mm (1.93 in) dia. 
  2. 41 mm (1.61 in) dia. 
KV40105320
(-)
Drift
G04901817Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side bearing outer race (clutch housing side)
  1. 88 mm (3.46 in) dia. 
ST33200000
(J-26082)
Drift
G04875596Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing mainshaft front bearing
  • Installing 6th input gear bushing
  • Installing 4th main gear
  • Installing 5th main gear
  • Installing 6th main gear

  1. 60 mm (2.36 in) dia. 
  2. 44.5 mm (1.752 in) dia. 
ST30720000
(J-25405)
Drift
G04876263Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing differential side oil seal (transaxle case side)
  • Installing differential side bearing outer race (clutch housing side)
  • Installing differential side bearing outer race (transaxle case side)
  • Installing mainshaft rear bearing
  • Installing differential side bearing (clutch housing side)
  • Installing differential side bearing (transaxle case side)

  1. 77 mm (3.03 in) dia. 
  2. 55.5 mm (2.185 in) dia. 
ST33061000
(J-8107-2)
Drift
G04876274Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing bore plug
  • Removing differential side bearing (transaxle case side)
  • Removing differential side bearing (clutch housing side)

  1. 38 mm (1.50 in) dia. 
  2. 28.5 mm (1.122 in) dia. 
ST33052000
(-)
Drift
G04875595Courtesy of NISSAN MOTOR CO., U.S.A.
  • Removing input shaft rear bearing
  • Removing 6th input gear, 6th input gear bushing, 5th-6th synchronizer hub assembly, and 5th input gear
  • Removing 5th input gear bushing, 4th input gear, 4th input gear bushing, 3rd-4th synchronizer hub assembly, and 3rd input gear
  • Installing input shaft front bearing
  • Removing mainshaft rear bearing
  • Removing 6th main gear
  • Removing 4th main gear and 5th main gear

  1. 22 mm (0.87 in) dia. 
  2. 28 mm (1.10 in) dia. 
KV40105020
(-)
Drift
G04876281Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing 3rd main gear, 2nd main gear, 2nd main gear bushing, 1st-2nd synchronizer hub assembly, 1st main gear, 1st main gear bushing, and reverse main gear
  1. 39.7 mm (1.563 in) dia. 
  2. 35 mm (1.38 in) dia. 
  3. 15 mm (0.59 in) 
ST30031000
(J-22912-01)
Puller
G04875583Courtesy of NISSAN MOTOR CO., U.S.A.
 Measuring wear of inner baulk ring
KV40105710
(-)
Press stand
G04888827Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing 3rd-4th synchronizer hub assembly
  • Installing 4th input gear bushing
  • Installing 5th input gear bushing
  • Installing 5th-6th synchronizer hub assembly
  • Installing 2nd main gear bushing
  • Installing 3rd main gear

  1. 46 mm (1.81 in) dia. 
  2. 41 mm (1.61 in) 
ST30901000
(J-26010-01)
Drift
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing input shaft rear bearing
  • Installing 4th main gear
  • Installing 5th main gear
  • Installing 6th main gear
  • Installing mainshaft rear bearing

  1. 79 mm (3.11 in) dia. 
  2. 45 mm (1.77 in) dia. 
  3. 35.2 mm (1.386 in) dia. 
ST30032000
(J-26010-01)
Drift
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing input shaft front bearing
  1. 80 mm (3.15 in) dia. 
  2. 38 mm (1.50 in) dia. 
  3. 31 mm (1.22 in) dia. 
ST38220000
(-)
Press stand
G04888827Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing reverse main gear
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly

  1. 63 mm (2.48 in) dia. 
  2. 65 mm (2.56 in) 
KV40101630
(J-35870)
Drift
G04901416Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing reverse main gear
  1. 68 mm (2.68 in) dia. 
  2. 60 mm (2.36 in) dia. 
KV38102510
(-)
Drift
G04888832Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly
  • Installing differential side bearing (transaxle case side)
  • Installing differential side bearing (clutch housing side)

  1. 71 mm (2.80 in) dia. 
  2. 65 mm (2.56 in) dia. 
-
(J-46534)
Trim tool set
G06558176Courtesy of NISSAN MOTOR CO., U.S.A.
 For removing trim
scientia non olet · About LEMON Manuals