LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2011 >> Sentra S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Engine Mechanical (Qr25DE)) >> Service Information >> Preparation >> Special Service Tool

Special Service Tool

WARNING: This page is about a different variant/trim than selected.

The actual shapes of the Kent-Moore tools may differ from those of the special service tools illustrated here.

SPECIAL SERVICE TOOL REFERENCE CHART

Tool number
(Kent-Moore No.)
Tool name		 Description
KV10111100
(J-37228)
Seal cutter
G07137389Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing steel oil pan and rear timing chain case
ST0501S000
Engine stand assembly
  1. ST05011000

    (-)

    Engine stand

  2. ST05012000

    (-)

    Base
G07137390Courtesy of NISSAN MOTOR CO., U.S.A.
 Disassembling and assembling
KV10106500
(-)
Engine stand shaft
G07137391Courtesy of NISSAN MOTOR CO., U.S.A.
  
KV10115300
(-)
Engine sub-attachment
G07137392Courtesy of NISSAN MOTOR CO., U.S.A.
  
KV10116200
(J-26336-B)
Valve spring compressor
  1. KV10115900

    (J-26336-20)

    Attachment
G07137393Courtesy of NISSAN MOTOR CO., U.S.A.
 Disassembling valve mechanism
KV10112100
(BT-8653-A)
Angle wrench
G07137394Courtesy of NISSAN MOTOR CO., U.S.A.
 Tightening bolts for bearing cap, cylinder head, etc.
KV10107902
(J-38959)
Valve oil seal puller
G07137395Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing valve oil seal
KV10115600
(J-38958)
Valve oil seal drift
G07137396Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing valve oil seal
Use side A. 
  1. 20 (0.79) dia. 
  2. 13 (0.51) dia. 
  3. 10.3 (0.406) dia. 
  4. 8 (0.31) dia. 
  5. 10.7 (0.421) dia. 
  6. 5 (0.20) dia. 

Unit: mm (in)
EM03470000
(J-8037)
Piston ring compressor
G07137397Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing piston assembly into cylinder bore
ST16610001
(J-23907)
Pilot bushing puller
G07137398Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing crankshaft pilot bushing
WS39930000
(-)
Tube presser
G07137399Courtesy of NISSAN MOTOR CO., U.S.A.
 Pressing the tube of liquid gasket
16441 6N210
(J-45488)
Quick connector release
G07137400Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing fuel tube quick connectors in engine room
(Available in SEC. 164 of PARTS CATALOG: Part No. 16441 6N210)
KV10114400
(J-38365)
Heated oxygen sensor wrench
G07137401Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening or tightening rear heated oxygen sensor
  1. 22 mm (0.87 in) 
KV10117100
(J-36471-A)
Heated oxygen sensor wrench
G07137402Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening or tightening heated oxygen sensor
For 22 mm (0.87 in) hexagon nut 
KV991J0050
(J-44626)
Air fuel ratio (A/F) sensor wrench
G07137403Courtesy of NISSAN MOTOR CO., U.S.A.
 Loosening or tightening air fuel ratio (A/F) sensor 1
-
(J-46535)
Drive belt tension releaser
G07137404Courtesy of NISSAN MOTOR CO., U.S.A.
 Releasing drive belt tension
scientia non olet · About LEMON Manuals