LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2011 >> Sentra S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (Manual Transmission - RS6F94R) >> Service Information >> Preparation >> Special Service Tool

Special Service Tool

WARNING: This page is about a different variant/trim than selected.

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

SPECIAL SERVICE TOOL REFERENCE CHART

Tool number
(Kent-Moore No.)
Tool name		 Description
KV381054S0
(J-34286)
Puller
G04875581Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing mainshaft front bearing outer race
KV38100200
(-)
Drift
G04876266Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing mainshaft front bearing outer race
  • Installing mainshaft rear bearing outer race
  • Installing differential side bearing outer race (clutch housing side)

  1. 65 mm (2.56 in) dia. 
  2. 49 mm (1.93 in) dia. 
ST33220000
(-)
Drift
G07138451Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing input shaft oil seal
  1. 37 mm (1.46 in) dia. 
  2. 31 mm (1.22 in) dia. 
  3. 22 mm (0.87 in) dia. 
ST33400001
(J-26082)
Drift
G04875582Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side bearing outer race (transaxle case side)
  1. 60 mm (2.36 in) dia. 
  2. 47 mm (1.85 in) dia. 
KV32500QAA
(Renault SST: B.vi 1666))
Drift set
G05914869Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side oil seal
  1. - (Stamping number: B.vi 1666-A) Drift
    1. 54.3 mm (2.138 in) dia. 
    2. 45 mm (1.77 in) dia. 
    3. 26.6 mm (1.047 in) dia. 
  2. - (Stamping number: B.vi 1666-B) Drift
    1. 54.3 mm (2.138 in) dia. 
    2. 45 mm (1.77 in) dia. 
    3. 26.6 mm (1.047 in) dia. 
ST36720030
(-)
Drift
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing input shaft rear bearing
  • Installing mainshaft front bearing inner race

  1. 70 mm (2.76 in) dia. 
  2. 40 mm (1.57 in) dia. 
  3. 29 mm (1.14 in) dia. 
ST33052000
(-)
Drift
G04926354Courtesy of NISSAN MOTOR CO., U.S.A.
  • Removing mainshaft rear bearing inner race
  • Removing 6th main gear
  • Removing 5th main gear
  • Removing 4th main gear
  • Removing 1st main gear
  • Removing 1st-2nd synchronizer assembly
  • Removing 2nd main gear
  • Removing bushing
  • Removing 3rd main gear
  • Removing mainshaft front bearing inner race

  1. 22 mm (0.87 in) dia. 
  2. 28 mm (1.10 in) dia. 
KV32102700
(-)
Drift
G04926355Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing bushing
  • Installing 2nd main gear
  • Installing 3rd main gear
  • Installing 4th main gear
  • Installing 5th main gear
  • Installing 6th main gear

  1. 54 mm (2.13 in) dia. 
  2. 32 mm (1.26 in) dia. 
ST30901000
(J-26010-01)
Drift
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing mainshaft rear bearing inner race
  1. 79 mm (3.11 in) dia. 
  2. 45 mm (1.77 in) dia. 
  3. 35.2 mm (1.386 in) dia. 
ST33061000
(J-8107-2)
Drift
G04926354Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing differential side bearing inner race (clutch housing side)
  1. 28.5 mm (1.122 in) dia. 
  2. 38 mm (1.50 in) dia. 
KV32300QAM
(Renault SST: B.vi 1823)
Drift
G05914875Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing and installing input shaft rear bearing bolt
-
(J-46534)
Trim tool set
G06558176Courtesy of NISSAN MOTOR CO., U.S.A.
 For removing trim
scientia non olet · About LEMON Manuals