Method Of Starting

Turn ignition switch OFF.
Turn ON the ignition switch with the trip reset switch (1) pressed.

Fig 1: Locating Trip Reset Switch
Courtesy of NISSAN MOTOR CO., U.S.A.
"TEST" is indicated in the top portion of the information display after a lapse of 6 seconds after the ignition switch is turned ON.
When the pressed trip reset switch is released within 3 seconds after the "TEST" indication, "WI code XX" is indicated in the top portion of the information display and On board diagnosis is started.
NOTE: On board diagnosis does not start if the trip reset switch is pressed for 3 seconds or more.

The mode switches in the order shown below each time the trip reset switch is pressed.

MODE SWITCHES REFERENCE CHART

Test order	Test item	Operation/Indication (Indicated in the top portion of Information Display)	Notes
1	Part No XXXXX	Part number is indicated.	-
2	Gauge sweep	Each gauge pointer sweeps.	The pointers sweep for 10 seconds. If any one of the pointers does not sweep, replace combination meter.
3	(All pixels illuminated)	All the dots of the information display illuminate.	If any dot does not illuminates, replace combination meter.
4	Telltales	All the warning lamps and indicator lamps turns ON.	If any one of the indicator lamps of warning lamps does not turn ON, replace combination meter.
5	ROM XXXX	"r XXXX" or "FAIL" is indicated.	If "FAIL" is indicated, replace combination meter.
6	N ROM XXXX	-	Not used
7	EE XX, FAIL	"EE XX" or "FAIL" is indicated.	If "FAIL" is indicated, replace combination meter.
8	Dtcs XXXXXX	-	Not used
9	Date XXXX	-	Not used
10	SCEM0 XX	-	Not used
11	SCEM1 XX	-	Not used
12	EprJmp XX	-	Not used
13	Market XX	-	Not used
14	TF a XXXX	-	Not used
15	TF b XXXX	-	Not used
16	OAT rad xxx	-	Not used
17	OAT xxx °C	-	Not used
18	DC Speed XXXX	-	Not used
19	Mph XXXXX	A vehicle speed signal value is indicated. (MPH)	The "--" indication means no signal reception. The "99999" indication means the reception of an abnormal signal.
20	Kmh XXXXX	A vehicle speed signal value is indicated. (km/h)	The "--" indication means no signal reception. The "99999" indication means the reception of an abnormal signal.
21	DC Tasho XXXX	-	Not used
22	Tacho XXXX	An engine speed signal value is indicated. (RPM)	The "--" indication means no signal reception.
23	DC Fuel XXXX	-	Not used
24	Fuel rad XXX	A fuel gauge signal value is indicated.	The "000" - "009" indications mean that the fuel gauge signal circuit is open. The "010" - "254" indication mean that the fuel gauge signal circuit is normal. The "255" indication means that the fuel gauge signal circuit is shorted. "-" is indicated for 5 seconds.
25	Fuel % xxx	-	Not used
26	FPhyst xxx	-	Not used
27	DC Temp XXXX	-	Not used
28	Temp ect XXX	A water temperature signal value is indicated. (°C)	The "- C" indication means no signal reception. The "999 C" indication means the reception of an abnormal signal.
29	Oil level xxxx	-	Not used
30	Batt XXX	-	Not used
31	Port A-XX	-	Not used
32	Port B-XX	-	Not used
33	Port C-XX	-	Not used
34	Port E-XX	-	Not used
35	Port L-XX	-	Not used
36	Port K-XX	-	Not used
37	Port M-XX	-	Not used
38	Port P-XX	-	Not used
39	Port S-XX	-	Not used
40	Port T-XX	-	Not used
41	Port U-XX	-	Not used
42	Port V-XX	-	Not used
43	Port W-XX	-	Not used
44	A00 XXX	-	Not used
45	A01 XXX	-	Not used
46	A02 XXX	-	Not used
47	A03 XXX	-	Not used
48	A04 XXX	-	Not used
49	A05 XXX	-	Not used
50	A06 XXX	-	Not used
51	A07 XXX	-	Not used
52	A08 XXX	-	Not used
53	A09 XXX	-	Not used
54	A10 XXX	-	Not used
55	A11 XXX	-	Not used
56	A12 XXX	-	Not used
57	A13 XXX	-	Not used
58	A14 XXX	-	Not used
59	A15 XXX	-	Not used
60	WI code XX	-	Not used
NOTE: "X" in the table shows a variable.