LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2008 >> Sentra SL >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Manual Transmission) >> RS6F52A >> Preparation >> Special Service Tools

Special Service Tools

WARNING: This page is about a different variant/trim than selected.

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

SPECIAL SERVICE TOOLS

Tool number
(Kent-Moore No.)
Tool name		 Description
KV381054S0
(J-34286)
Puller
G04875581Courtesy of NISSAN MOTOR CO., U.S.A.
  • Removing differential side bearing outer race (clutch housing side)
  • Removing differential side bearing outer race (transaxle case side)
  • Removing mainshaft front bearing
ST33400001
(J-26082)
Drift
  1. 60 mm (2.36 in) dia.
  2. 47 mm (1.85 in) dia.
G04875582Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side oil seal (clutch housing side)
ST35321000
( - )
Drift
  1. 49 mm (1.93 in) dia.
  2. 41 mm (1.61 in) dia.
G04876274Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing input shaft oil seal
  • Installing reverse main gear
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly
  • Installing 2nd main gear bushing
  • Installing 3rd main gear
KV40105320
( - )
Drift
  1. 88 mm (3.46 in) dia.
G04901817Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing differential side bearing outer race (clutch housing side)
ST33200000
(J-26082)
Drift
  1. 60 mm (2.36 in) dia.
  2. 44.5 mm (1.752 in) dia.
G04875596Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing mainshaft front bearing
  • Installing 6th input gear bushing
  • Installing 4th main gear
  • Installing 5th main gear
  • Installing 6th main gear
ST30720000
(J-25405)
Drift
  1. 77 mm (3.03 in) dia.
  2. 55.5 mm (2.185 in) dia.
G04876263Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing differential side oil seal (transaxle case side)
  • Installing differential side bearing outer race (clutch housing side)
  • Installing differential side bearing outer race (transaxle case side)
  • Installing mainshaft rear bearing
  • Installing differential side bearing (clutch housing side)
  • Installing differential side bearing (transaxle case side)
ST33061000
(J-8107-2)
Drift
  1. 38 mm (1.50 in) dia.
  2. 28.5 mm (1.122 in) dia.
G04876274Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing bore plug
  • Removing differential side bearing (transaxle case side)
  • Removing differential side bearing (clutch housing side)
ST33052000
( - )
Drift
  1. 22 mm (0.87 in) dia.
  2. 28 mm (1.10 in) dia.
G04875595Courtesy of NISSAN MOTOR CO., U.S.A.
  • Removing input shaft rear bearing
  • Removing 6th input gear, 6th input gear bushing, 5th-6th synchronizer hub assembly, and 5th input gear
  • Removing 5th input gear bushing, 4th input gear, 4th input gear bushing, 3rd-4th synchronizer hub assembly, and 3rd input gear
  • Installing input shaft front bearing
  • Removing mainshaft rear bearing
  • Removing 6th main gear
  • Removing 4th main gear and 5th main gear
KV40105020
( - )
Drift
  1. 39.7 mm (1.563 in) dia.
  2. 35 mm (1.38 in) dia.
  3. 15 mm (0.59 in)
G04876281Courtesy of NISSAN MOTOR CO., U.S.A.
 Removing 3rd main gear, 2nd main gear, 2nd main gear bushing, 1st-2nd synchronizer hub assembly, 1st main gear, 1st main gear bushing, and reverse main gear
ST30031000
(J-22912-01)
Puller
G04875583Courtesy of NISSAN MOTOR CO., U.S.A.
 Measuring wear of inner bulk ring
KV40105710
( - )
Press stand
  1. 46 mm (1.81 in) dia.
  2. 41 mm (1.61 in)
G04888827Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing 3rd-4th synchronizer hub assembly
  • Installing 4th input gear bushing
  • Installing 5th input gear bushing
  • Installing 5th-6th synchronizer hub assembly
  • Installing 2nd main gear bushing
  • Installing 3rd main gear
ST30901000
(J-26010-01)
Drift
  1. 79 mm (3.11 in) dia.
  2. 45 mm (1.77 in) dia.
  3. 35.2 mm (1.386 in) dia.
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing input shaft rear bearing
  • Installing 4th main gear
  • Installing 5th main gear
  • Installing 6th main gear
  • Installing mainshaft rear bearing
ST30032000
(J-26010-01)
Drift
  1. 80 mm (3.15 in) dia.
  2. 38 mm (1.50 in) dia.
  3. 31 mm (1.22 in) dia.
G04876276Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing input shaft front bearing
ST38220000
( - )
Press stand
  1. 63 mm (2.48 in) dia.
  2. 65 mm (2.56 in)
G04888827Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing reverse main gear
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly
KV40101630
(J-35870)
Drift
  1. 68 mm (2.68 in) dia.
  2. 60 mm (2.36 in) dia.
G04901416Courtesy of NISSAN MOTOR CO., U.S.A.
 Installing reverse main gear
KV38102510
( - )
Drift
  1. 71 mm (2.80 in) dia.
  2. 65 mm (2.56 in) dia.
G04888832Courtesy of NISSAN MOTOR CO., U.S.A.
  • Installing 1st main gear bushing
  • Installing 1st-2nd synchronizer hub assembly
  • Installing differential side bearing (transaxle case side)
  • Installing differential side bearing (clutch housing side)
(J-39713)
Preload adapter
G04888833Courtesy of NISSAN MOTOR CO., U.S.A.
 Measuring end play of side gear
scientia non olet · About LEMON Manuals