LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Altima S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 998 (Automatic Drive Positioner) >> Component Diagnosis >> Mirror Sensor >> Passenger Side >> PASSENGER SIDE: Diagnosis Procedure

PASSENGER SIDE: Diagnosis Procedure

WARNING: This page is about a different car, the 2009 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DOOR MIRROR RH SENSOR SIGNAL
    1. Turn ignition switch to ACC.
    2. Check voltage between door mirror RH harness connector and ground.
    Fig 1: Checking Voltage Between Door Mirror RH Harness Connector And Ground
    G05877577Courtesy of NISSAN MOTOR CO., U.S.A.
    VOLTAGE REFERENCE CHART

    Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    Door mirror RH connector Terminal
    D107 12 Ground Door mirror RH Close to peak 3.4
    Close to valley 0.6
    11 Close to right edge 3.4
    Close to left edge 0.6

    Is the inspection result normal? 

    YES: GO TO  5

    NO: GO TO 2

  2. CHECK DOOR MIRROR RH SENSOR CIRCUIT 1
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit and door mirror RH.
    3. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
      CONTINUITY REFERENCE CHART

      Automatic drive positioner control unit connector Terminal Door mirror RH connector Terminal Continuity
      M63 (A) 5 D107 (B) 12 Yes
      17 11
      Fig 2: Checking Continuity Between Automatic Drive Positioner Control Unit Connector And Door Mirror RH Connector
      G05877581Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between automatic drive positioner control unit harness connector and ground.
    CONTINUITY REFERENCE CHART

    Automatic drive positioner control unit connector Terminal Ground Continuity
    M63 (A) 5 No
    17

    Is the inspection result normal? 

    YES: GO TO 3

    NO: Repair or replace harness.

  3. CHECK DOOR MIRROR RH SENSOR CIRCUIT 2
    1. Check continuity between automatic drive positioner control unit harness connector and door mirror RH harness connector.
      CONTINUITY REFERENCE CHART

      Automatic drive positioner control unit connector Terminal Door mirror RH connector Terminal Continuity
      M63 (A) 20 D107 (B) 9 Yes
      21 10
    2. Check continuity between automatic drive positioner control unit harness connector and ground.
    Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Harness Connector And Ground
    G05877579Courtesy of NISSAN MOTOR CO., U.S.A.
    CONTINUITY REFERENCE CHART

    Automatic drive positioner control unit connector Terminal Ground Continuity
    M63 (A) 20 No
    21

    Is the inspection result normal? 

    YES: GO TO 4

    NO: Repair or replace harness.

  4. CHECK TILT MOTOR ADJUSTING OPERATION
    1. Connect automatic drive positioner control unit and door mirror RH.
    2. Turn ignition switch ON.
    3. Check tilt motor adjusting operation with memory function.

    Is the operation normal? 

    YES: Replace door mirror actuator. (Built in door mirror RH). Refer to "REMOVAL AND INSTALLATION ".

    NO: Replace automatic drive positioner control unit. Refer to "REMOVAL AND INSTALLATION ".

  5. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    Is the inspection result normal? 

    YES: Replace automatic drive positioner control unit. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace the malfunctioning part.

scientia non olet · About LEMON Manuals