LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Altima S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 996 (Power Window Control System) >> LH & RH Front Window Anti-Pinch >> Component Diagnosis >> Power Supply And Ground Circuit >> Front Power Window Switch >> FRONT POWER WINDOW SWITCH: Diagnosis Procedure

FRONT POWER WINDOW SWITCH: Diagnosis Procedure

WARNING: This page is about a different car, the 2009 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK POWER SUPPLY CIRCUIT

    Check voltage between power window and door lock/unlock switch RH connector D105 terminal 10 and ground.

    VOLTAGE SPECIFICATION

    Terminal Voltage (V) (Approx.)
    (+) (-)
    Power window and door lock/unlock switch RH connector Terminal
    D105 10 Ground Battery voltage
    Fig 1: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector And Ground
    G05046793Courtesy of NISSAN MOTOR CO., U.S.A.

    Is the inspection result normal? 

    YES: GO TO  3

    NO: GO TO 2

  2. CHECK HARNESS CONTINUITY
    1. Turn ignition switch OFF.
    2. Disconnect BCM connector M16 and power window and door lock/unlock switch RH connector.
    3. Check continuity between BCM connector M16 (A) terminal 2 and power window and door lock/unlock switch RH connector D105 (B) terminal 10.
      CONTINUITY SPECIFICATION

      BCM connector Terminal Power window and door lock/unlock switch RH connector Terminal Continuity
      M16 (A) 2 D105 (B) 10 Yes
      Fig 2: Checking Continuity Between BCM Connector And Ground
      G05046794Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between BCM connector M16 (A) terminal 2 and ground.
    CONTINUITY SPECIFICATION

    BCM connector Terminal Ground Continuity
    M16 (A) 2 No

    Is the inspection result normal? 

    YES: Replace BCM. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace harness or connectors.

  3. CHECK GROUND CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect power window and door lock/unlock switch RH.
    3. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 11 and ground.
    CONTINUITY SPECIFICATION

    Power window and door lock/unlock switch RH Terminal Ground Continuity
    D105 11 Yes

    Is the inspection result normal? 

    YES: Inspection End.

    NO: Repair or replace harness or connectors.

Fig 3: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Connector And Ground
G05046795Courtesy of NISSAN MOTOR CO., U.S.A.


  1. CHECK POWER SUPPLY CIRCUIT

    Check voltage between power window and door lock/unlock switch RH connector D105 terminal 10 and ground.

    VOLTAGE SPECIFICATION

    Terminal Voltage (V) (Approx.)
    (+) (-)
    Power window and door lock/unlock switch RH connector Terminal
    D105 10 Ground Battery voltage
    Fig 1: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector And Ground
    G05046793Courtesy of NISSAN MOTOR CO., U.S.A.

    Is the inspection result normal? 

    YES: GO TO  3

    NO: GO TO 2

  2. CHECK HARNESS CONTINUITY
    1. Turn ignition switch OFF.
    2. Disconnect BCM connector M16 and power window and door lock/unlock switch RH connector.
    3. Check continuity between BCM connector M16 (A) terminal 2 and power window and door lock/unlock switch RH connector D105 (B) terminal 10.
      CONTINUITY SPECIFICATION

      BCM connector Terminal Power window and door lock/unlock switch RH connector Terminal Continuity
      M16 (A) 2 D105 (B) 10 Yes
      Fig 2: Checking Continuity Between BCM Connector And Ground
      G05046794Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check continuity between BCM connector M16 (A) terminal 2 and ground.
    CONTINUITY SPECIFICATION

    BCM connector Terminal Ground Continuity
    M16 (A) 2 No

    Is the inspection result normal? 

    YES: Replace BCM. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace harness or connectors.

  3. CHECK GROUND CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect power window and door lock/unlock switch RH.
    3. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 11 and ground.
    CONTINUITY SPECIFICATION

    Power window and door lock/unlock switch RH Terminal Ground Continuity
    D105 11 Yes

    Is the inspection result normal? 

    YES: Inspection End.

    NO: Repair or replace harness or connectors.

Fig 3: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Connector And Ground
G05046795Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals