Door Mirror Remote Control Switch (Mirror Switch) Circuit Check

WARNING: This page is about a different car, the 2007 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.

CHECK FUNCTION

With CONSULT-II

Check operation with "MIR CON SW-UP/DN, MIR CON SW-RH/LH" on the DATA MONITOR to make sure pulse changes.

MIR CON SW MONITOR ITEM CHART

Monitor item [OPERATION or UNIT]		Contents
MIR CON SW-UP	"ON/OFF"	ON/OFF status judged from the door mirror remote control switch (UP) signal is displayed.
MIR CON SW-DN	"ON/OFF"	ON/OFF status judged from the door mirror remote control switch (DOWN) signal is displayed.
MIR CON SW-RH	"ON/OFF"	ON/OFF status judged from the door mirror remote control switch (RIGHT) signal is displayed.
MIR CON SW-LH	"ON/OFF"	ON/OFF status judged from the door mirror remote control switch (LEFT) signal is displayed.

Fig 1: CONSULT-II Display - DATA MONITOR

Courtesy of NISSAN MOTOR CO., U.S.A.

Without CONSULT-II

Turn ignition switch to ACC.
Check voltage between automatic drive positioner control unit connector and ground.

AUTOMATIC DRIVE POSITIONER CONTROL UNIT CONNECTOR AND GROUND

Connector	Terminals		Condition	Voltage (V) (Approx.)
Connector	(+)	(-)	Condition	Voltage (V) (Approx.)
M41	3	Ground	Mirror switch UP operation	0
	3		Other than above	5
	4		Mirror switch LEFT operation	0
	4		Other than above	5
	19		Mirror switch DOWN operation	0
	19		Other than above	5
	20		Mirror switch RIGHT operation	0
	20		Other than above	5

Fig 2: Checking Voltage Between Automatic Drive Positioner Control Unit Connector And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: Door mirror remote control switch (mirror switch) circuit is OK.

NG: GO TO 2.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH CIRCUIT HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror remote control switch.
3. Check continuity between automatic drive positioner control unit connector M41 terminals 3, 4, 19, 20 and door mirror remote control switch connector M7 terminals 4, 4, 6, 14.
  3 - 6: Continuity should exist.
  
  4 - 5: Continuity should exist.
  
  19 - 14: Continuity should exist.
  
  20 - 4: Continuity should exist.
4. Check continuity between automatic drive positioner control unit connector M41 terminals 3, 4, 19, 20 and ground.
  3 - Ground: Continuity should not exist.
  
  4 - Ground: Continuity should not exist.
  
  19 - Ground: Continuity should not exist.
  
  20 - Ground: Continuity should not exist.
Fig 3: Checking Door Mirror Remote Control Switch Circuit Harness Continuity
Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: GO TO 3.

NG: Repair or replace harness.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH)

Check continuity between door mirror remote control switch terminals as follows.

DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH)

Terminals		Condition	Continuity
4	13	Mirror switch RIGHT operation	Yes
4		Other than above	No
5		Mirror switch LEFT operation	Yes
5		Other than above	No
6		Mirror switch UP operation	Yes
6		Other than above	No
14		Mirror switch DOWN operation	Yes
14		Other than above	No

Fig 4: Checking Continuity Between Door Mirror Remote Control Switch Terminals

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: Check the condition of the harness and the connector.

NG: Replace door mirror remote control switch.