Headlamp Low Beam Does Not Illuminate (Both Sides)

With CONSULT-II

Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor, make sure "HEAD LAMP SW 1" and "HEAD LAMP SW 2" turns ON-OFF linked with operation of lighting switch.

When lighting switch is in 2ND position 

: HEAD LAMP SW 1 ON 

: HEAD LAMP SW 2 ON 

Without CONSULT-II

Refer to "COMBINATION SWITCH INSPECTION ".

Fig 1: CONSULT-II Display - DATA MONITOR

OK or NG 

OK: GO TO 2.

NG: Check lighting switch. Refer to "COMBINATION SWITCH INSPECTION ".

With CONSULT-II

1. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
2. Select "LAMPS" on "SELECT TEST ITEM" screen.
3. Touch "LO" on "ACTIVE TEST" screen.
4. Make sure headlamp low beam operates.

   Headlamp low beam should operate. 

Without CONSULT-II

1. Start auto active test. Refer to "AUTO ACTIVE TEST ".
2. Make sure headlamp low beam operates.

   Headlamp low beam should operate. 

Fig 2: CONSULT-II Display - ACTIVE TEST

OK or NG 

OK: GO TO 3.

NG: GO TO  4.

1. Select "IPDM E/R" on CONSULT-II, and select "DATA MONITOR" on "SELECT DIAG MODE" screen.
2. Make sure "HL LO REQ" turns ON when lighting switch is in 2ND position.

   When lighting switch is in 2ND position: HL LO REQ ON 

Fig 3: CONSULT-II Display - DATA MONITOR

OK or NG 

OK: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION OF IPDM E/R ".

NG: Replace BCM. Refer to "BCM ".

With CONSULT-I I

1. Turn ignition switch OFF.
2. Disconnect front combination lamp RH and LH connectors.
3. Turn ignition switch ON.
4. Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
5. Select "LAMPS" on "SELECT TEST ITEM" screen.
6. Touch "LO" on "ACTIVE TEST" screen.
7. When headlamp low beam is operating, check voltage between front combination lamp RH and LH harness connectors and ground.

Without CONSULT-II

1. Turn ignition switch OFF.
2. Disconnect front combination lamp RH and LH connectors.
3. Start auto active test. Refer to "AUTO ACTIVE TEST ".
4. When headlamp low beam is operating, check voltage between front combination lamp RH and LH harness connectors and ground.
   FRONT COMBINATION LAMP RH AND LH HARNESS CONNECTORS AND GROUND
   
   

   Terminals				Voltage
   (+)			(-)
   Front combination lamp connector		Terminal
   RH	E107	3	Ground	Battery voltage
   LH	E11

   Fig 4: Checking Voltage Between Front Combination Lamp RH And LH Connectors And Ground

   

OK or NG 

OK: GO TO  6.

NG: GO TO 5.

1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector E122 terminal 20 and front combination lamp RH harness connector E107 terminal 3.

   20 - 3: Continuity should exist. 

4. Check continuity between IPDM E/R harness connector E122 terminal 30 and front combination lamp LH harness connector E11 terminal 3.

   30 - 3: Continuity should exist. 

Fig 5: Checking Continuity Between IPDM E/R Connector E122 Terminal 30 And Front Combination Lamp LH Harness Connector E11 Terminal 3

OK or NG 

OK: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION OF IPDM E/R ".

NG: Repair harness or connector.

1. Turn ignition switch OFF.
2. Check continuity between front combination lamp RH harness connector E107 terminal 4 and ground.

   4 - Ground: Continuity should exist. 

3. Check continuity between front combination lamp LH harness connector E11 terminal 4 and ground.

   4 - Ground: Continuity should exist. 

Fig 6: Checking Continuity Between Front Combination Lamp LH Connector E11 Terminal 4 And Ground

OK or NG 

OK: Check headlamp harness and connectors, ballasts (HID control unit), and xenon bulbs. Refer to "XENON HEADLAMP TROUBLE DIAGNOSIS ".

NG: Repair harness or connector.