Limit Switch Circuit Check Rear LH and RH (With Front and Rear Anti-pinch System)

WARNING: This page is about a different car, the 2007 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.

CHECK REAR POWER WINDOW MOTOR LH AND RH LIMIT SWITCH SIGNAL

Turn ignition switch ON.

Check voltage between rear power window switch LH or RH connector and ground.

REAR POWER WINDOW SWITCH LH OR RH CONNECTOR AND GROUND

Connector	Terminals		Condition	Voltage (V) (Approx.)
Connector	(+)	(-)	Condition	Voltage (V) (Approx.)
D203 (LH) D303 (RH)	15	Ground	Rear power window LH or RH is between fully-open and just before fully-closed position (ON)	0
D203 (LH) D303 (RH)	15	Ground	Rear power window LH or RH is between just before fully-closed position and fully-closed position (OFF)	5

Fig 1: Checking Voltage Between Rear Power Window Switch LH Or RH Connector And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: Limit switch circuit is OK.

NG: GO TO 2.

CHECK LIMIT SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH or RH.
3. Check continuity between rear power window motor LH or RH connector D204 (LH), D304 (RH) terminal 6 and ground.
  6 - Ground: Continuity should exist.
Fig 2: Checking Continuity Between Rear Power Window Motor LH Or RH Connector Terminal 6 And Ground
Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: GO TO 4.

NG: GO TO 3.
CHECK HARNESS CONTINUITY
Check continuity between rear power window motor LH or RH connector D204 (LH), D304 (RH) terminal 6 and rear power window switch LH or RH connector D203 (LH), D303 (RH) terminal 3.

6 - 3: Continuity should exist.

Fig 3: Checking Harness Continuity
Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: Replace rear power window switch LH or RH. Refer to "REAR DOOR ".

NG: Repair or replace harness.
CHECK REAR POWER WINDOW SWITCH LH OR RH OUTPUT SIGNAL
Check voltage between rear power window switch LH or RH harness connector D203 (LH) or D303 (RH) terminal 15 and ground.

15 - Ground: Approx. 5V

Fig 4: Checking Voltage Between Rear Power Window Switch LH Or RH Harness Connector Terminal 15 And Ground
Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: GO TO 5.

NG: Replace rear power window switch LH or RH. Refer to "REAR DOOR ".
CHECK HARNESS CONTINUITY
Check continuity between rear power window switch LH or RH connector D203 (LH), D303 (RH) terminal 15 and rear power window motor LH or RH connector D204 (LH), D304 (RH) terminal 2.

15 - 2: Continuity should exist.

Fig 5: Checking Harness Continuity
Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: GO TO 6.

NG: Repair or replace harness.

CHECK LIMIT SWITCH

Connect rear power window motor LH or RH and rear power window switch LH or RH.
Turn ignition switch ON.

Check continuity between rear power window motor LH or RH connector D204 (LH), D304 (RH) terminal 2 and 6.

REAR POWER WINDOW MOTOR LH OR RH CONNECTOR D204 (LH), D304 (RH) TERMINAL 2 AND 6

Connector	Terminals		Condition	Continuity
D204 (LH) D304(RH)	2	6	Rear power window LH or RH is between fully-open and just before fully-closed position (ON)	Yes
D204 (LH) D304(RH)	2	6	Rear power window LH or RH is between just before fully-closed position and fully-closed position (OFF)	No

Fig 6: Checking Continuity Between Rear Power Window Motor LH Or RH Connector Terminal 2 And 6

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG

OK: Repair or replace harness.

NG: Replace rear power window motor LH or RH. Refer to "REAR DOOR GLASS AND REGULATOR ".