LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Altima S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1165 (Engine Control System - DTCS P0137 To P0448) >> P0139, P0159 Ho2S2 >> Diagnosis Procedure

Diagnosis Procedure

WARNING: This page is about a different car, the 2009 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK GROUND CONNECTION
    1. Turn ignition switch OFF.
    2. Check ground connection E9. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

      Is the inspection result normal? 

      YES: GO TO 2.

      NO: Repair or replace ground connection.

  2. CLEAR MIXTURE RATIO SELF-LEARNING VALUE
    1. Clear the mixture ratio self-learning value. Refer to "MIXTURE RATIO SELF-LEARNING VALUE CLEAR: SPECIAL REPAIR REQUIREMENT ".
    2. Run engine for at least 10 minutes at idle speed.

      Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected? Is it difficult to start engine? 

      YES: Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. Refer to "DTC LOGIC " or "DTC LOGIC ".

      NO: GO TO 3.

  3. CHECK HO2S2 GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect heated oxygen sensor 2 harness connector.
    3. Disconnect ECM harness connector.
    4. Check the continuity between heated oxygen sensor 2 (HO2S2) harness connector and ECM harness connector.
      TERMINAL CONNECTOR REFERENCE CHART

      DTC HO2S2 ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0139 1 F62 1 F13 35 Existed
      P0159 2 F56 1
    5. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 4.

      NO: Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between HO2S2 harness connector and ECM harness connector.
      TERMINAL CONNECTOR REFERENCE CHART

      DTC HO2S2 ECM Continuity
      Bank Connector Terminal Connector Terminal
      P0139 1 F62 4 F13 33 Existed
      P0159 2 F56 4 34
    2. Check the continuity between HO2S2 harness connector and ground, or ECM harness connector and ground.
      TERMINAL CONNECTOR REFERENCE CHART

      DTC HO2S2 Ground Continuity
      Bank Connector Terminal
      P0139 1 F62 4 Ground Not existed
      P0159 2 F56 4
      TERMINAL CONNECTOR REFERENCE CHART

      DTC ECM Ground Continuity
      Connector Terminal
      P0139 F13 33 Ground Not existed
      P0159 34
    3. Also check harness for short to power.

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: Repair open circuit, short to ground or short to power in harness or connectors.

  5. CHECK HEATED OXYGEN SENSOR 2

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 7.

    NO: GO TO 6.

  6. REPLACE HEATED OXYGEN SENSOR 2

    Replace malfunctioning heated oxygen sensor 2.

    CAUTION:
    • Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
    • Before installing new oxygen sensor, clean exhaust system threads using Oxygen Sensor Thread Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).

    : INSPECTION END

  7. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals