LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Altima S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1061 (Front Axle) >> Unit Disassembly And Assembly >> Drive Shaft >> VK56DE >> VK56DE: Disassembly and Assembly >> Assembly

VK56DE: Disassembly and Assembly: Assembly

WARNING: This page is about a different car, the 2012 Nissan Pathfinder. However, it is still accessible from the selected car via links, so may be relevant.

Final Drive Side

  1. Wrap the serrated part of the drive shaft with tape. Install the boot band and boot to drive shaft.
    NOTE: Discard the old boot band and boot and use a new one for assembly.
    Fig 1: Removing Tape Wound Around Serrated Part Of Shaft
    G04876506Courtesy of NISSAN NORTH AMERICA, INC.
  2. Remove the tape wound around the serrated part of the drive shaft.
  3. Install the ball cage, steel ball, and inner race assembly on the drive shaft, and secure them tightly using the snap ring.
    NOTE: Discard the old snap ring and use a new one for assembly.
    Fig 2: Identifying Ball Cage, Shaft And Snap Ring
    G04876507Courtesy of NISSAN NORTH AMERICA, INC.
  4. Insert the specified quantity of Genuine NISSAN Grease or equivalent, onto the housing (indicated by * marks), and install it onto shaft. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS ".

    Grease capacity: Refer to  "VK56DE: DRIVE SHAFT ".

    Fig 3: Identifying Genuine NISSAN Grease Applying Areas On Housing
    G04876508Courtesy of NISSAN NORTH AMERICA, INC.
  5. Install the stopper ring onto the housing.
  6. After installation, pull on the shaft to check engagement between the sliding joint and the stopper ring.
  7. Install the boot securely into the grooves (indicated by * marks) as shown in illustration below.
    CAUTION: If there is grease on boot mounting surfaces (indicated by * marks) of shaft and housing, boot may come off. Remove all grease from surfaces.
  8. Check that the boot installation length (L) is the length indicated below. Insert a suitable tool into the large end of the boot. Bleed air from the boot to prevent boot deformation.

    Boot installation length (L): Refer to  "VK56DE: DRIVE SHAFT ".

    Fig 4: Installing Boot Securely Into Grooves
    G04902006Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • The boot may break if the boot installation length is less than the specified value.
    • Do not to touch the tip of the suitable tool to the inside of the boot.
  9. Secure the large and small ends of the boot with the new boot bands as shown in illustration below.
    NOTE: Discard the old boot bands and use new ones for assembly.
    Fig 5: Securing Boot Bands
    G05378027Courtesy of NISSAN NORTH AMERICA, INC.
  10. After installing the sliding joint housing to the drive shaft, rotate the boot to check that the boot is positioned correctly. If the boot is not positioned correctly, reposition the boot and secure the boot using a new boot band.

Wheel Side

  1. Insert the Genuine NISSAN Grease or equivalent, into the joint sub-assembly serration hole until the grease begins to ooze from the ball groove and serration hole. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS ". After inserting the grease, use a shop cloth to wipe off the grease that has oozed out.
    Fig 6: Applying Grease Into Joint Sub-Assembly
    G04876511Courtesy of NISSAN NORTH AMERICA, INC.
  2. Wrap the serrated part of the drive shaft with tape. Install the boot band and boot onto the shaft. Do not damage the boot.
    NOTE: Discard the old boot band and boot and use a new one for assembly.
  3. Remove the protective tape wound around the serrated part of the drive shaft.
    Fig 7: Removing Tape Wound Around Serrated Part Of Shaft
    G04876506Courtesy of NISSAN NORTH AMERICA, INC.
  4. Attach the circlip to the drive shaft. The circlip must fit securely into the drive shaft groove. Attach the nut to the joint sub-assembly.

    Use a soft hammer to press-fit the circlip.

    NOTE: Discard the old circlip and use a new one for assembly.
  5. Insert the specified quantity of Genuine NISSAN Grease or equivalent, into the joint sub-assembly and the large end of the boot. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS ".

    Grease capacity: Refer to  "VK56DE: DRIVE SHAFT ".

    Fig 8: Installing Circlip To Drive Shaft
    G07019352Courtesy of NISSAN NORTH AMERICA, INC.
  6. Install the boot securely into the grooves (indicated by the * marks) as shown in illustration below.
    CAUTION: If there is grease on the boot mounting surfaces (indicated by the * marks) of the drive shaft and joint sub-assembly, the boot may come off. Remove all grease from the drive shaft surfaces.
  7. Check that the boot installation length (L) is the specified length. Insert a suitable tool into the large end of the boot. Bleed the air from the boot to prevent boot deformation.

    Boot installation length (L): Refer to  "VK56DE: DRIVE SHAFT ".

    Fig 9: Installing Boot Securely Into Grooves
    G05892947Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • The boot may break if the boot installation length is less than the specified length.
    • Do not contact inside surface of boot with the tip of the suitable tool.
  8. Secure large and small ends of the boot using new boot bands using tool as shown in illustration below.

    Tool number: KV40107300 (-) 

    NOTE: Discard the old boot bands and use new ones for assembly.
    Fig 10: Tightening Boot Band Using Boot Band Crimping Tool
    G04902012Courtesy of NISSAN NORTH AMERICA, INC.
    • Secure boot band so that dimension (M) meets specification as shown in illustration below.

      Dimension (M): Refer to  "VK56DE: BOOT BANDS ".

      Fig 11: Identifying Boot Band Dimension
      G07015951Courtesy of NISSAN NORTH AMERICA, INC.
  9. After installing the housing to the shaft, rotate the boot to check that it is positioned correctly. If the boot is not positioned correctly, remove the old boot bands then reposition the boot and secure the boot with new boot bands.
scientia non olet · About LEMON Manuals