FRONT DOOR REQUEST SWITCH: Diagnosis Procedure

Regarding Wiring Diagram information, refer to "WIRING DIAGRAM ".

1. CHECK FRONT DOOR REQUEST SWITCH

   With CONSULT 

   Check front door request switch ("DR REQ SW" or "AS REQ SW") in "DATA MONITOR" mode.

   Monitor Item	Condition
   DR REQ SW AS REQ SW	Front door request switch is pressed: ON
   	Front door request switch is released: OFF

   Without CONSULT 

   1. Turn ignition switch OFF.
   2. Check voltage between Intelligent Key unit harness connector M70 terminals 5, 25 and ground.

   Connector	Item	Terminals		Condition	Voltage (V) (Approx.)
   		(+)	(-)
   M70	Front door request switch LH	5	Ground	Door request switch is pressed ↓ Door request switch is released	0 ↓ Battery voltage
   	Front door request switch RH	25

   Fig 1: Checking Voltage Between Intelligent Key Unit Harness Connector M70 Terminals 5, 25 And Ground

   Courtesy of NISSAN NORTH AMERICA, INC.

   Is the inspection result normal? 

   YES: Front door request switch is OK.

   NO: GO TO 2

2. CHECK FRONT DOOR REQUEST SWITCH CIRCUIT
   1. Turn ignition switch OFF.
   2. Disconnect Intelligent Key unit and front door request switch connectors.
   3. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 5 (driver door), 25 (passenger door) and front door request switch harness connector (B) D16 (LH), D116 (RH) terminal 2.

      Driver side 5 - 2: Continuity should exist  .

      Passenger side 25 - 2: Continuity should exist  .

   4. Check continuity between Intelligent Key unit harness connector (A) M70 terminals 5 (driver door), 25 (passenger door) and ground.

      5 - Ground: Continuity should not exist  .

      25 - Ground: Continuity should not exist  .

      Fig 2: Checking Continuity Between Intelligent Key Unit Harness Connector M70 And Front Door Request Switch Harness Connector D16 Terminals

      Courtesy of NISSAN NORTH AMERICA, INC.

      Is the inspection result normal? 

      YES: GO TO 3

      NO: Repair or replace harness between Intelligent Key unit and front door request switch.

3. CHECK FRONT DOOR REQUEST SWITCH GROUND CIRCUIT

   Check continuity between front door request switch harness connector D16 (driver door), D116 (passenger door) terminal 1 and ground.

   1 - Ground: Continuity should exist  .

   Is the inspection result normal? 

   YES: GO TO 4

   NO: Repair or replace door request switch ground circuit.

   Fig 3: Checking Continuity Between Front Door Request Switch Harness Connector D16 (Driver Door), D116 (Passenger Door) Terminal 1 And Ground

   Courtesy of NISSAN NORTH AMERICA, INC.
4. CHECK FRONT DOOR REQUEST SWITCH OPERATION

   Refer to "FRONT DOOR REQUEST SWITCH: COMPONENT INSPECTION ".

   Is the inspection result normal? 

   YES: GO TO 5

   NO: Replace front door request switch.

5. CHECK FRONT DOOR REQUEST SWITCH SIGNAL
   1. Connect Intelligent Key unit connector.
   2. Check voltage between Intelligent Key unit harness connector M70 terminals 5, 25 and ground.

   Connector	Item	Terminals		Condition	Voltage (V) (Approx.)
   		(+)	(-)
   M70	Front door request switch LH	5	Ground	Door request switch is pressed ↓ Door request switch is released	0 ↓ Battery voltage
   	Front door request switch RH	25

   Fig 4: Checking Voltage Between Intelligent Key Unit Harness Connector M70 Terminals 5, 25 And Ground

   Courtesy of NISSAN NORTH AMERICA, INC.

   Is the inspection result normal? 

   YES: Refer to "INTERMITTENT INCIDENT ".

   NO: Replace Intelligent Key unit. Refer to "REMOVAL AND INSTALLATION ".