Crankshaft Main & Connecting Rod Bearings
WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
CRANKSHAFT MAIN & CONNECTING ROD BEARINGS
| Application | In. (mm) | ||
|---|---|---|---|
| Crankshaft | |||
| End Play | |||
| Standard | .0039-.0098 (.10-.25) | ||
| Service Limit | .0118 (.30) | ||
| Runout | .0039 (.10) | ||
| Main Bearings | |||
| Journal Diameter | |||
| Grade No. A | 2.3612-2.3612 (59.974-59.975) | ||
| Grade No. B | 2.3611-2.3612 (59.973-59.974) | ||
| Grade No. C | 2.3611-2.3611 (59.972-59.973) | ||
| Grade No. D | 2.3611-2.3611 (59.971-59.972) | ||
| Grade No. E | 2.3610-2.3611 (59.970-59.971) | ||
| Grade No. F | 2.3610-2.3610 (59.969-59.970) | ||
| Grade No. G | 2.3610-2.3609 (59.968-59.969) | ||
| Grade No. H | 2.3609-2.3609 (59.967-59.968) | ||
| Grade No. J | 2.3609-2.3609 (59.966-59.967) | ||
| Grade No. K | 2.3608-2.3609 (59.965-59.966) | ||
| Grade No. L | 2.3608-2.3608 (59.964-59.965) | ||
| Grade No. M | 2.3607-2.3608 (59.963-59.964) | ||
| Grade No. N | 2.3607-2.3607 (59.962-59.963) | ||
| Grade No. P | 2.3607-2.3607 (59.961-59.962) | ||
| Grade No. R | 2.3606-2.3607 (59.960-59.961) | ||
| Grade No. S | 2.3606-2.3606 (59.959-59.960) | ||
| Grade No. T | 2.3605-2.3606 (59.958-59.959) | ||
| Grade No. U | 2.3605-2.3605 (59.957-59.958) | ||
| Grade No. V | 2.3605-2.3605 (59.956-59.957) | ||
| Grade No. W | 2.3604-2.3605 (59.955-59.956) | ||
| Grade No. X | 2.3604-2.3604 (59.954-59.955) | ||
| Grade No. Y | 2.3603-2.3604 (59.953-59.954) | ||
| Grade No. 4 | 2.3603-2.3603 (59.952-59.953) | ||
| Grade No. 7 | 2.3603-2.3603 (59.951-59.922) | ||
| Journal Out-Of-Round | .0001 (.002) | ||
| Journal Taper | .0001 (.002) | ||
| Oil Clearance | |||
| Standard | .0014-.0018 (.035-.045) | ||
| Service Limit | .0026 (.065) | ||
| Connecting Rod Bearings | |||
| Journal Diameter | |||
| Grade No. 0 | 2.0460-2.0462 (51.968-51.974) | ||
| Grade No. 1 | 2.0457-2.0460 (51.962-51.968) | ||
| Grade No. 2 | 2.0445-2.0457 (51.956-51.962) | ||
| Journal Out-Of-Round | .0001 (.002) | ||
| Journal Taper | .0001 (.002) | ||
| Oil Clearance | |||
| Standard | .0013-.0023 (.034-.059) | ||
| Service Limit | .0028 (.070) | ||