Data Monitor
WARNING: This page is about a different car, the 2012 Nissan Pathfinder. However, it is still accessible from the selected car via links, so may be relevant.
Operation Procedure
- Connect CONSULT.
- Touch DATA MONITOR.
- Select from SELECT MONITOR ITEM, screen of data monitor mode is displayed.NOTE: When malfunction is detected, CONSULT performs REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
| x: Standard -: Not applicable | ||||
|---|---|---|---|---|
| Monitor Item (Unit) | Selection | Description | ||
| ECU INPUT SIGNALS | MAIN SIGNALS | SELECTION FROM MENU | ||
| VHCL/S SEN.FR [km/h] or [mph] | x | - | x | Wheel speed calculated by ABS actuator and electric unit (control unit). Signal input with CAN communication line. |
| VHCL/S SEN.RR [km/h] or [mph] | x | - | x | Wheel speed calculated by TCM. Signal input with CAN communication line. |
| ENGINE SPEED [rpm] | x | - | x | Engine speed calculated by ECM. Signal input with CAN communication line. |
| THRTL POS SEN [0.0/8] | x | - | x | Accelerator pedal position (APP) sensor status is displayed. Signal input with CAN communication line. |
| FLUID TEMP SE [V] | x | - | x | Transfer fluid temperature sensor signal voltage is displayed. |
| BATTERY VOLT [V] | x | - | x | Power supply voltage for transfer control unit. |
| 2WD SWITCH [On/Off] | x | - | x | 4WD shift switch status is displayed. |
| AUTO SWITCH [On/Off] | x | - | x | 4WD shift switch status is displayed. |
| LOCK SWITCH [On/Off] | x | - | x | 4WD shift switch status is displayed. (LOCK means 4H of 4WD shift switch.) |
| 4L SWITCH [On/Off] | x | - | x | 4WD shift switch status is displayed. (4L means 4LO of 4WD shift switch.) |
| N POSI SW TF [On/Off] | x | - | x | Neutral-4LO switch signal status is displayed. |
| ATP SWITCH [On/Off] | x | - | x | ATP switch signal status is displayed. |
| WAIT DETCT SW [On/Off] | x | - | x | Wait detection switch status is displayed. |
| LINE PRES SW [On/Off] | x | - | x | Line pressure switch status is displayed. |
| CL PRES SW [On/Off] | x | - | x | Clutch pressure switch status is displayed. |
| N POSI SW AT [On/Off] | x | - | x | N position signal of transmission range switch status is displayed. Signal input with CAN communication line. |
| R POSI SW AT [On/Off] | x | - | x | R position signal of transmission range switch status is displayed. Signal input with CAN communication line. |
| P POSI SW AT [On/Off] | x | - | x | P position signal of transmission range switch status is displayed. Signal input with CAN communication line. |
| ABS OPER SW [On/Off] | x | - | x | ABS operation signal status is displayed. Signal input with CAN communication line. |
| VDC OPER SW [On/Off] | x | - | x | VDC operation signal status is displayed. Signal input with CAN communication line. |
| TCS OPER SW [On/Off] | x | - | x | TCS operation signal status is displayed. Signal input with CAN communication line. |
| THROTTLE POSI [0.0/8] | - | x | x | Throttle position status is displayed. Signal input with CAN communication line. |
| 4WD MODE [AUTO/LOCK/2WD/4L] | - | x | x | Control status of 4WD recognized by transfer control unit. (AUTO, 4H, 2WD or 4LO) |
| VHCL/S COMP [km/h] or [mph] | - | x | x | Vehicle speed recognized by transfer control unit. |
| COMP CL TORQ [kgm] | - | x | x | Calculated torque recognized by transfer control unit. |
| DUTY SOLENOID [%] | - | x | x | Control value of clutch pressure solenoid. |
| 2-4WD SOL [On/Off] | - | x | x | Output condition to 2-4WD solenoid. |
| 2-4WD SOL MON [On/Off] | - | - | x | Check signal for transfer control unit signal output. |
| MOTOR RELAY [On/Off] | - | x | x | Transfer motor relay signal status is displayed. |
| MOTOR RLY MON [On/Off] | - | - | x | Check signal for transfer control unit signal output. |
| 4WD FAIL LAMP [On/Off] | - | x | x | Control status of 4WD warning lamp is displayed. |
| 2WD IND [On/Off] | - | - | x | Control status of 4WD shift indicator lamp (2WD indicator lamp) is displayed. |
| AUTO IND [On/Off] | - | - | x | Control status of 4WD shift indicator lamp (2WD and AUTO indicator lamp) is displayed. |
| LOCK IND [On/Off] | - | - | x | Control status of 4WD shift indicator lamp (2WD, AUTO and Lock indicator) is displayed. |
| 4L IND [On/Off] | - | - | x | Control status of 4LO indicator lamp is displayed. |
| ATP IND [On/Off] | - | - | x | Control status of ATP warning lamp is displayed. |
| SHIFT POS SW1 [On/Off] | x | - | x | Actuator position switch 1 (Low) signal status is displayed. |
| SHIFT POS SW2 [On/Off] | x | - | x | Actuator position switch 2 (high) signal status is displayed. |
| SHIFT ACT 1 [On/Off] | - | x | x | Output condition to actuator motor (clockwise) |
| SHIFT AC MON1 [On/Off] | x | - | x | Check signal for transfer control unit signal output |
| SHIFT ACT 2 [On/Off] | - | x | x | Output condition to actuator motor (counterclockwise) |
| SHIFT AC MON2 [On/Off] | x | - | x | Check signal for transfer control unit signal output |
| T/F F SPEED [km/h] or [mph] | x | - | x | Displayed, but do not use. |
| A/T R SPEED [km/h] or [mph] | x | - | x | Output shaft revolution signal (output speed sensor) calculated by TCM. Signal input with CAN communication line. |
| AT GEAR POSI [1/2/3/4/5] | x | - | x | A/T actual g ear position is displayed. |