Display Item DTC List
WARNING: This page is about a different car, the 2004 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
ABS MALFUNCTION DETECTING CONDITION DTCS
| DTC | Malfunction detecting condition | Check system | ||||
|---|---|---|---|---|---|---|
| FR LH SENSOR 1 [C1104] |
Circuit of front LH wheel sensor is open | "Wheel Sensor System Inspection" (Note 1) | ||||
| RR RH SENSOR 1 [C1101] |
Circuit of rear RH wheel sensor is open | |||||
| FR RH SENSOR 1 [C1103] |
Circuit of front RH wheel sensor is open | |||||
| RR LH SENSOR 1 [C1102] |
Circuit of rear LH wheel sensor is open | |||||
| FR LH SENSOR 2 [C1108] |
Circuit of front LH wheel sensor is shorted, or sensor power voltage is unusual. ABS actuator and electric unit (control unit) cannot identify sensor pulses, because of large gap between wheel sensor and sensor rotor. | |||||
| RR RH SENSOR 2 [C1105] |
Circuit of rear RH wheel sensor is shorted, or sensor power voltage is unusual. ABS actuator and electric unit (control unit) cannot identify sensor pulses, because of large gap between wheel sensor and sensor rotor. | |||||
| FR RH SENSOR 2 [C1107] |
Circuit of front RH wheel sensor is shorted, or sensor power voltage is unusual. ABS actuator and electric unit (control unit) cannot identify sensor pulses, because of large gap between wheel sensor and sensor rotor. | |||||
| RR LH SENSOR 2 [C1106] |
Circuit of rear LH wheel sensor is shorted, or sensor power voltage is unusual. ABS actuator and electric unit (control unit) cannot identify sensor pulses, because of large gap between wheel sensor and sensor rotor. | |||||
| STOP LAMP SW 1 [C1116] |
Stop lamp switch or circuit malfunction. | "Stop Lamp Switch System Inspection" | ||||
| FR LH IN ABS SOL [C1120] |
Circuit of front LH IN ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | - | ||||
| FR LH OUT ABS SOL [C1121] |
Circuit of front LH OUT ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| RR RH IN ABS SOL [C1126] |
Circuit of rear RH IN ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| RR RH OUT ABS SOL [C1127] |
Circuit of rear RH OUT ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| FR RH IN ABS SOL [C1122] |
Circuit of front RH IN ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| FR RH OUT ABS SOL [C1123] |
Circuit of front RH OUT ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| RR LH IN ABS SOL [C1124] |
Circuit of rear LH IN ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| RR LH OUT ABS SOL [C1125] |
Circuit of rear LH OUT ABS solenoid is open or shorted, or control line is open or shorted to power supply or ground. | |||||
| PUMP MOTOR (Note (2)) [C1111] |
During actuator motor operation with ON, when actuator motor turns OFF or when control line for actuator motor relay is open. | "Actuator Motor, Motor Relay, and Circuit Inspection" | ||||
| During actuator motor operation with OFF, when actuator motor turns ON or when control line for relay is shorted to ground. | ||||||
| BATTERY VOLTAGE [ABNORMAL] [C1109] |
ABS actuator and electric unit (control unit) power voltage is too low. | "ABS Control Unit Power and Ground Systems Inspection" | ||||
| CONTROLLER FAILURE [C1110] |
Internal malfunction of ABS actuator and electric unit (control unit) | "ABS Control Unit Inspection" | ||||
| CAN COMM CIRCUIT [U1000] |
|
"CAN Communication System Inspection" (Note (1)) | ||||
| BR FLUID LEVEL LOW [C1155] |
Brake fluid level drops or circuit between ABS actuator and electric unit (control unit) and brake fluid level switch is open or shorted. | "WARNING LAMPS" | ||||
| ENGINE SPEED SIG | Engine speed signal from ECM is abnormal. | "Engine System Inspection" | ||||
| ENGINE SIGNAL 1 [C1130] |
ECM judges the communication between ABS control unit and ECM is abnormal. | "CAN Communication System Inspection" | ||||
| STOP LAMP SW 2 [C1176] |
ASCD brake switch or circuit malfunction. | "ASCD BRAKE SWITCH" | ||||
Note 1. If wheel sensor 2 for each wheel is indicated, check ABS actuator and electric unit (control unit) power supply voltage in addition to wheel sensor circuit check.
|
||||||
Note 1. If wheel sensor 2 for each wheel is indicated, check ABS actuator and electric unit (control unit) power supply voltage in addition to wheel sensor circuit check.
Note 2. If multiple malfunctions are detected including CAN communication line [U1000], perform diagnosis for CAN communication line first.
Note 3: "ACTUATOR RLY" on the CONSULT-II self-diagnosis results indicates the malfunction of the actuator motor relay or circuit.