LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2017 >> Lancer SE >> Repair and Diagnosis >> External Pages >> Different car >> Section 84 (Twin Clutch-SPORTRONIC Shift Transmission (TC-SST) - With Diagnostics - Lancer (1 Of 6)) >> Diagnosis < TC-SST > >> TC-SST Teach-In >> Teach-In Procedure

Teach-In Procedure

WARNING: This page is about a different car, the 2015 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • According to the transmission fluid state (fluid-filled state), Teach-In executed time is not equal.
  • Item No. 8 is not displayed when the Diag. Version of TC-SST-ECU is 0001. (Diag. Version can be checked by the Teach-In screen of scan tool.)
MECHATRONIC ASSEMBLY REPLACEMENT DESCRIPTION

Steps Contents
1 With the scan tool connected and the vehicle set to the condition below, execute the Teach-In.
  • Engine: Idling
  • Shift lever position: P range
  • Brake pedal: Depressed
  • Parking brake: Pulled
  • Transmission fluid temperature: 40°C to 80°C (104°F to 176°F)
2 Select "Special Function" of TC-SST.
3 Select "Teach-In" of Special Function.
4 According to "2-2 Item execution order", select the Item No. 1: Plausibility check to execute.
NOTE: Before execution, "No" is displayed in the Data list No. 100: Teach-In executing.
5 After execution, check that "Yes" is displayed in the Data list No. 100: Teach-In executing.
NOTE: In a case other than the execution conditions, "Pending" is displayed in the Data list No. 100: Teach-In executing.
6 After the Teach-In (Item No. 1: Plausibility check) completion, check that "No" is displayed in the Data list No. 100: Teach-In executing and execution results are displayed in the Data list No. 101 to No. 104.
  • No. 101: Normal End: On normal end, "Yes" is displayed.
  • No. 102: Abnormal End: On abnormal end, "Yes" is displayed.
  • No. 103: Timeout error: On timeout error, "Yes" is displayed
  • No. 104: Abort conditions error: In a case other than the execution conditions, "Yes" is displayed.
7 Change the item to No. 2: Shift fork Teach-In, and execute steps from 5 to 6 in the same manner.
8 Turn the ignition switch to the LOCK (OFF) position.
To store the learned value in the memory, make sure that the TC-SST-ECU is shut down by turning the ignition switch OFF.
9 Start the engine again, and execute step 1 in the same manner.
10 Change the item to No. 1: Plausibility Check, and execute steps from 5 to 6 in the same manner.
11
CAUTION: Item No. 7: If the clutch ventilation "fails", first follow steps 12 to 15, and then steps 9 to 11. Item No. 7: If the clutch ventilation "completes successfully", repeat steps 12 to 15.
Change the item to No. 7: Clutch Ventilation, and execute steps from 5 to 6 in the same manner.
12 Change the item to No. 4: Stroke Teach-In, and execute steps from 5 to 6 in the same manner.
13
CAUTION: Be careful with the following items when performing Item No. 5: Boost Teach-In.
  • The engine speed could be high (4, 000 r/min) when the Boost Teach-In is in progress. (Depending on the transaxle state, the engine speed may not be high.)
Change the item to No. 5: Boost Teach-In, and execute steps from 5 to 6 in the same manner.
14 Change the item to No. 8: Reset clutch gain, and execute steps from 5 to 6 in the same manner. When the Diag. Version of TC-SST-ECU is 0001, Item No. 8 is not used.
15 Turn the ignition switch to the LOCK (OFF) position.
CLUTCH ASSEMBLY REPLACEMENT DESCRIPTION

Contents
Execute the mechatronic assembly replacement procedures form 1 to 3, and from 10 to 15.
scientia non olet · About LEMON Manuals