DTC B1C2A: Side-airbag Module (LH) (Squib) System (Short Circuit between Squib Circuit Terminals): Diagnosis

Required Special Tools:

MB991958 Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: Vehicle Communication Interface (V.C.I.)
- MB991827 M.U.T.-III USB Cable
- MB991910 M.U.T.-III Main Harness A (Vehicles with CAN communication system)
MB991865: Dummy resistor
MB991866: Resister harness

STEP 1. Using scan tool MB991958, diagnose the CAN bus line.
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958. Refer to "HOW TO CONNECT THE SCAN TOOL ."
2. Connect scan tool MB991958 to the data link connector.
3. Turn the ignition switch to "ON" position.
4. Diagnose the CAN bus line.
Q: Is the check result satisfactory?
- YES: Go to Step 2.
- NO: Repair the CAN bus line (Refer to DIAGNOSIS ).
  
  Fig 1: Connecting Special Tool MB991910 To Data Link Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 2. Recheck for diagnostic trouble code.
Check again if the DTC is set.
1. Erase the DTC.
2. Turn the ignition switch to "ON" position.
3. Check if the DTC is set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
- YES: Go to Step 3.
- NO: There is an intermittent malfunction such as poor engaged connector(s) or open circuit (Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTION ).
STEP 3. Check SRS-ECU connector C-30 and side-airbag module (LH) connector D-30.
1. Disconnect the negative battery terminal.
2. While pressing the part A in the illustration of the C-30 SRS-ECU harness side connector, turn the lock lever toward the arrow direction to release the lock lever. Then, disconnect the connector and reconnect it.
  
  Fig 2: Turning Lock Lever
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Disconnect the D-30 side-airbag module connector, and then reconnect it, unlock the connector by sliding the locking button to the direction of the arrow as shown in the illustration , and then disconnect the connector.
4. Connect the negative battery terminal.
5. Erase the diagnostic trouble code memory, and check the diagnostic trouble code.
Q: Is DTC B1C2A out put?
- YES: Go to Step 4.
- NO: The procedure is complete. It is assumed that DTC B1C2A set because connector C-30 or D-30 was engaged improperly.
  
  Fig 3: Disconnecting Side-Airbag Module Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 4. Check the side-airbag module (LH).
1. Disconnect the negative battery terminal.
2. Disconnect the D-30 side-airbag module connector, unlock the connector by sliding the locking button to the direction of the arrow as shown in the illustration , and then disconnect the connector.
  
  Fig 4: Disconnecting Side-Airbag Module Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
3. Connect special tool MB991865 to special tool MB991866.
  CAUTION: Do not insert a test probe into the terminal from its front side directly, as the connector contact pressure may be weakened.
4. Insert special tool MB991866 into the D-30 harness side connector by backprobing.
5. Connect the negative battery terminal.
6. Erase diagnostic trouble code memory, and check the diagnostic trouble code.
Q: Is DTC B1C2A set?
- YES: Go to Step 5.
- NO: Replace the front seatback assembly (Refer to DISASSEMBLY AND ASSEMBLY ) < Except RALLIART >, or replace the front seatback (Refer to DISASSEMBLY AND ASSEMBLY ) < RALLIART >. Then go to Step 7.
  
  Fig 5: Connecting Special Tool MB991865 To Special Tool MB991866
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 5. Check the side-airbag module (LH) circuit. Measure the resistance at the SRS-ECU connector C-30.
1. Disconnect the negative battery terminal.
2. While pushing the part "A" indicated in the illustration of the harness side connector, turn the lock lever to the direction of the arrow to release the lock lever, and disconnect the C-30 SRS-ECU connector.
  
  Fig 6: Turning Lock Lever
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  
  WARNING: To prevent the air bag from deploying unintentionally, disconnect the side-airbag module (LH) connector D-30 to short the squib circuit.
3. Disconnect the D-30 side-airbag module connector, unlock the connector by sliding the locking button to the direction of the arrow as shown in the illustration , and then disconnect the connector.
  
  Fig 7: Disconnecting Side-Airbag Module Connector
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  
  CAUTION: Insert an insulator such as a cable tie to a depth of 4mm (0.16 inch) or more, otherwise the short spring will not be released.
4. Insert a cable tie [3 mm (0.12 inch) wide, 0.5 mm (0.02 inch) thick] between terminals 31, 32 and the short spring to release the short spring.
  
  Fig 8: Inserting Cable Tie Wide Thick Between Terminals 31, 32 And Short Spring
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
5. Check for continuity between C-30 harness side connector terminals 31 and 32. It should be an open circuit.
Q: Is it open circuit?
- YES: Erase the diagnostic trouble code memory, and check the diagnostic trouble code. If DTC B1C2A sets, replace the SRS-ECU (Refer to SRS CONTROL UNIT (SRS-ECU) ). Then go to Step 7.
- NO: Go to Step 6.
  
  Fig 9: Checking Continuity Between C-30 Harness Side Connector Terminals 31 And 32
  Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
STEP 6. Check the harness wires for short circuit between SRS-ECU connector C-30 (terminal No. 31 and 32) and side-airbag module (LH) connector D-30 (terminal No. 2 and 1).
Q: Is the check result normal?
- YES: Go to Step 7.
- NO: Repair the harness wires between SRS-ECU connector C-30 and side-airbag module (LH) connector D-30. Then go to Step 7.
STEP 7. Recheck for diagnostic trouble code.
Check again if the DTC is set.
1. Erase the DTC.
2. Turn the ignition switch to the "ON" position.
3. Check if the DTC is set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is DTC B1C2A set?
- YES: Return to Step 1.
- NO: The procedure is complete.