Section 21 (MULTIPORT Fuel Injection (MFI) - 2.4L - Lancer - Diagnostic Trouble Code Procedures - DTC P0010 Through DTC P0134)

• Diagnostic Trouble Code Procedures
  • DTC P0010: Intake Engine Oil Control Valve Circuit
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0011: Intake Variable Valve Timing System Target Error
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0013: Exhaust Engine Oil Control Valve Circuit
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0014: Exhaust Variable Valve Timing System Target Error
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0016: Crankshaft/camshaft (intake) Position Sensor Phase Problem
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0017: Crankshaft/camshaft (exhaust) Position Sensor Phase Problem
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0031: Linear Air-Fuel Ratio Sensor Heater Control Circuit Low
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0032: Linear Air-Fuel Ratio Sensor Heater Control Circuit High
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0037: Heated Oxygen Sensor (rear) Heater Control Circuit Low
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0038: Heated Oxygen Sensor (rear) Heater Control Circuit High
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0053: Linear Air-Fuel Ratio Sensor Heater Resistance
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0068: Mass Airflow Sensor Plausibility
    • Technical Description
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be stored are:)
    • Diagnosis
  • DTC P0069: Abnormal Correlation Between Manifold Absolute Pressure Sensor And Barometric Pressure Sensor
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0101: Mass Airflow Circuit Range/Performance Problem
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC SET CONDITIONS < Range/Performance problem - high >
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • DTC SET CONDITIONS < Range/Performance problem - low >
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0102: Mass Airflow Circuit Low Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0103: Mass Airflow Circuit High Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0106: Manifold Absolute Pressure Circuit Range/Performance Problem
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC SET CONDITIONS < Range/Performance problem - high input >
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • DTC SET CONDITIONS < Range/Performance problem - low input >
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0107: Manifold Absolute Pressure Circuit Low Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0108: Manifold Absolute Pressure Circuit High Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0111: Intake Air Temperature Circuit Range/Performance Problem
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0112: Intake Air Temperature Circuit Low Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0113: Intake Air Temperature Circuit High Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0116: Engine Coolant Temperature Circuit Range/Performance Problem
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criteria
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0117: Engine Coolant Temperature Circuit Low Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0118: Engine Coolant Temperature Circuit High Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0121: Throttle Position Sensor (main) Plausibility
    • Technical Description
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgment Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be stored are:)
    • Diagnosis
  • DTC P0122: Throttle Position Sensor (main) Circuit Low Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0123: Throttle Position Sensor (main) Circuit High Input
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Condition
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0125: Insufficient Coolant Temperature for Closed Loop Fuel Control
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC SET CONDITIONS < Range/Performance problem - drift >
      • Logic Flow Chart
      • Check Conditions, Judgement Criteria
    • DTC SET CONDITIONS < Range/Performance problem - low input (Time to reach closed loop temperature) >
      • Logic Flow Chart
      • Check Conditions, Judgement Criteria
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0130: Linear Air-Fuel Ratio Sensor Circuit
    • Notes
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criteria
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0131: Linear Air-Fuel Ratio Sensor Circuit Low Voltage
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0132: Linear Air-Fuel Ratio Sensor Circuit High Voltage
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0133: Linear Air-Fuel Ratio Sensor Circuit Slow Response
    • Notes
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criteria
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis
  • DTC P0134: Linear Air-Fuel Ratio Sensor Circuit No Activity Detected
    • Notes
    • Circuit Operation
    • Technical Description
    • Descriptions Of Monitor Methods
    • Monitor Execution
    • MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
      • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
      • Sensor (The sensor below is determined to be normal)
    • DTC Set Conditions
      • Logic Flow Chart
      • Check Conditions
      • Judgement Criterion
    • Fail-Safe And Backup Function
    • OBD-II Drive Cycle Pattern
    • TROUBLESHOOTING HINTS (The most likely causes for this code to be set are:)
    • Diagnosis