Torque Specifications
WARNING: This page is about a different car, the 2014 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
| Item | Specification |
|---|---|
| Generator and ignition system | |
| Idler pulley bolt | 44 ± 8 N.m (32 ± 5 ft-lb) |
| Generator nut | 44 ± 10 N.m (32 ± 7 ft-lb) |
| Generator bolt | 44 ± 10 N.m (32 ± 7 ft-lb) |
| Drive belt auto-tensioner bolt | 22 ± 4 N.m (16 ± 2 ft-lb) |
| Accessory bracket bolt | 44 ± 8 N.m (32 ± 5 ft-lb) |
| Crankshaft pulley center bolt | 210 N.m (155 ft-lb), 0N.m (0 ft-lb) then 210 N.m (155 ft-lb) |
| Ignition coil bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Spark plug | 25 ± 5 N.m (18 ± 3 ft-lb) |
| Throttle body | |
| Vacuum pipe and hose bolt | 11 ± 1 N.m (97 ± 8 in-lb) |
| Throttle body bolt | 9.5 ± 2.5 (84 ± 22 in-lb) |
| Purge control solenoid valve screw | 4.0 ± 1.0 (35 ± 8 in-lb) |
| Manifold absolute pressure (MAP) sensor screw | 4.0 ± 1.0 (35 ± 8 in-lb) |
| Inlet manifold and fuel system | |
| Injector protector rear bolt | 3.5 ± 1.5 N.m (31 ± 13 in-lb) then 20 ± 2 N.m (15 ± 1 ft-lb) |
| Fuel rail bolt | 3.5 ± 1.5 N.m (31 ± 13 in-lb) then 20 ± 2 N.m (15 ± 1 ft-lb) |
| Inlet manifold stay bolt | 20 ± 2 N.m (15 ± 1 ft-lb) |
| Injector protector front bolt | 3.5 ± 1.5 N.m (31 ± 13 in-lb) then 20 ± 2 N.m (15 ± 1 ft-lb) |
| Inlet manifold bolt and nut | 3.5 ± 1.5 N.m (31 ± 13 in-lb) then 20 ± 2 N.m (15 ± 1 ft-lb) |
| Oil level gauge guide bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Knock sensor bolt | 20 ± 2 N.m (15 ± 1 ft-lb) |
| Engine oil pressure switch | 10 ± 2 N.m (89 ± 17 in-lb) |
| Exhaust manifold | |
| Exhaust manifold bracket bolt (Exhaust manifold side) | 56 ± 8 N.m (41 ± 5 ft-lb) |
| Exhaust manifold bracket bolt (Cylinder block side) | 41 ± 10 N.m (30 ± 7 ft-lb) |
| Crank angle sensor cover bolt | 11 ± 1 N.m (97 ± 8 in-lb) |
| Crank angle sensor bolt | 11 ± 1 N.m (97 ± 8 in-lb) |
| Oxygen sensor | 44 ± 5 N.m (32 ± 3 ft-lb) |
| Exhaust manifold cover bolt | 14 ± 1 N.m (124 ± 8 in-lb) |
| Exhaust manifold nut | 49 ± 5 N.m (36 ± 3 ft-lb) |
| Water hose and pipe | |
| Engine coolant temperature sensor | 30 ± 9 N.m (22 ± 6 ft-lb) |
| Water outlet fitting bolt | 24 ± 3 N.m (18 ± 2 ft-lb) |
| Water inlet fitting bolt | 24 ± 3 N.m (18 ± 2 ft-lb) |
| Thermostat housing bolt | 24 ± 3 N.m (18 ± 2 ft-lb) |
| Water pipe nut | 24 ± 3 N.m (18 ± 2 ft-lb) |
| Water pump bolt | 24 ± 3 N.m (18 ± 2 ft-lb) |
| Valve lift control motor | |
| Camshaft position sensor bolt | 11 ± 1 N.m (97 ± 8 in-lb) |
| Valve lift control motor bolt | 9.5 ± 2.5 N.m (84 ± 22 ft-lb) |
| Motor bracket bolt | 21 ± 5 N.m (15 ± 3 ft-lb) |
| Valve lift sensor bolt | 2.8 ± 0.8 N.m (25 ± 7 in-lb) |
| Engine hanger bolt | 28 ± 8 N.m (21 ± 5 ft-lb) |
| Oil pan and timing chain case | |
| PCV valve | 2.5 ± 0.4 N.m (22 ± 3 in-lb) |
| Oil drain plug | 39 ± 5 N.m (29 ± 3 ft-lb) |
| Oil filter | 14 ± 2 N.m (124 ± 17 in-lb) |
| Filter insert | 49 ± 5 N.m (36 ± 3 ft-lb) |
| Rocker cover bolt | 3.0 ± 1.0 N.m (27 ± 8 in-lb) then 5.5 ± 0.5 (49 ± 4 in-lb) |
| Oil pan bolt < M6 > | 10 ± 2 N.m (89 ± 17 in-lb) |
| Oil pan bolt < M8 > | 31 ± 2 N.m (23 ± 1 ft-lb) |
| Timing chain case cover bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Timing chain case bolt < M6 > | 10 ± 2 N.m (89 ± 17 in-lb) |
| Timing chain case bolt < M8 > | 24 ± 4 N.m (18 ± 2 ft-lb) |
| Timing chain case bolt < M10 > | 35 ± 5 N.m (26 ± 3 ft-lb) |
| Timing chain | |
| Timing chain tensioner bolt | 11 ± 3 N.m (97 ± 26 in-lb) |
| Tensioner lever bolt | 11 ± 3 N.m (97 ± 26 in-lb) |
| Timing chain guide bolt | 11 ± 3 N.m (97 ± 26 in-lb) |
| Rocker arm and camshaft assembly | |
| Oil feeder control valve (OCV) bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Rocker arm and camshaft assembly bolt | 22 ± 3 N.m (16 ± 2 ft-lb) |
| Lock nut | 9.0 ± 1.0 N.m (80 ± 8 in-lb) |
| V.V.T. sprocket bolt | 77 ± 6 N.m (57 ± 4 ft-lb) |
| Cylinder head and valves | |
| Cylinder head bolt | 35 ± 2 N.m (26 ± 1 ft-lb), +90° then +90° |
| Balancer chain | |
| Balancer shaft chain guide bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Balancer shaft chain tensioner bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Balancer shaft module bolt | 20 N.m (15 ft-lb), 32 N.m(15 ft-lb), 0 N.m, (0 ft-lb) 20 N.m (15 ft-lb) then +135° |
| Balancer shaft tensioner lever bolt | 10 ± 2 N.m (89 ± 17 in-lb) |
| Drive plate bolt | 40 N.m (30 ft-lb) then 130 N.m (96 ft-lb) |
| Ladder frame bolt | 24 ± 2N.m (18 ± 1 ft-lb) |
| Piston and connecting rod | |
| Connecting rod cap bolt | 5.0N.m (44 in-lb), 20 N.m(15 ft-lb) then +90° |
| Crankshaft and cylinder block | |
| Crankshaft bearing cap bolt | 26.5 ± 2.0 N.m (20 ± 2.0 ft-lb) then +45° |
| Crankshaft sensing ring bolt | 11 ± 1 N.m (97 ± 8 in-lb) |