Section 96 (MULTIPORT Fuel Injection (MFI) - Lancer Evolution - Diagnostic Trouble Code Procedures - DTC P0830 Through DTC U1180)
WARNING: This page is about a different car, the 2012 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- DTC P0830: Clutch Pedal Position Switch Circuit Range/Performance
- DTC P1231: Active Stability Control Plausibility
- DTC P1236: A/D Converter
- DTC P1238: Mass Airflow Sensor Plausibility (Torque Monitor)
- DTC P1240: Ignition Angle
- DTC P1242: Fail Safe Control Monitor
- DTC P1243: Inquiry/Response Error
- DTC P1245: Cycle RAM Test (Engine)
- DTC P1247: TC-SST Plausibility
- DTC P1506: Idle Control System RPM Lower Than Expected At Low Temperature
- DTC P1507: Idle Control System RPM Higher Than Expected At Low Temperature
- DTC P1590: TCM To ECM Communication Error In Torque Reduction Request
- DTC P1603: Battery Backup Circuit Malfunction
- DTC P2066: Fuel Level Sensor (Sub) Circuit Range/Performance
- DTC P2096: Post Catalyst Fuel Trim System Too Lean
- DTC P2097: Post Catalyst Fuel Trim System Too Rich
- DTC P2100: Throttle Actuator Control Motor Circuit (Open)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2101: Throttle Actuator Control Motor Magneto Malfunction
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2122: Accelerator Pedal Position Sensor (Main) Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2123: Accelerator Pedal Position Sensor (Main) Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2127: Accelerator Pedal Position Sensor (Sub) Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2128: Accelerator Pedal Position Sensor (Sub) Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2135: Throttle Position Sensor (Main And Sub) Range/Performance Problem
- Notes
- THROTTLE POSITION SENSOR (Main And Sub) RANGE/PERFORMANCE PROBLEM CIRCUIT
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC SET CONDITIONS
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2138: Accelerator Pedal Position Sensor (Main And Sub) Range/Performance Problem
- Notes
- ACCELERATOR PEDAL POSITION SENSOR (Main And Sub) RANGE/PERFORMANCE PROBLEM CIRCUIT
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC SET CONDITIONS
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P2195: Heated Oxygen Sensor (Front) Inactive
- DTC P2228: Barometric Pressure Circuit Low Input
- DTC P2229: Barometric Pressure Circuit High Input
- DTC P2252: Heated Oxygen Sensor Offset Circuit Low Voltage
- DTC P2253: Heated Oxygen Sensor Offset Circuit High Voltage
- DTC P2263: Intake Charge System Malfunction
- DTC P2530: Ignition Switch Run Position Circuit
- DTC U0001: Bus Off
- DTC U0101: TC-SST-ECU Time-Out
- DTC U0121: ASC-ECU Time-Out
- DTC U0141: ETACS-ECU Time-Out
- DTC U0167: Immobilizer Communication Error
- DTC U1180: Combination Meter Time-Out