Section 93 (MULTIPORT Fuel Injection (MFI) - Lancer Evolution - Diagnostic Trouble Code Procedures - DTC P0010 Through DTC P0128)
WARNING: This page is about a different car, the 2012 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Trouble Code Procedures
- DTC P0010: Intake Engine Oil Control Valve Circuit
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0011: Intake Variable Valve Timing System Target Error
- DTC P0012: Camshaft Position - Timing Over-Retarded
- DTC P0013: Exhaust Engine Oil Control Valve Circuit
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0014: Exhaust Variable Valve Timing System Target Error
- DTC P0016: Crankshaft/Camshaft (Intake) Position Sensor Phase Problem
- DTC P0017: Crankshaft/Camshaft (Exhaust) Position Sensor Phase Problem
- DTC P0031: Heated Oxygen Sensor (Front) Heater Circuit Low
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0032: Heated Oxygen Sensor (Front) Heater Circuit High
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0037: Heated Oxygen Sensor (Rear) Heater Circuit Low
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0038: Heated Oxygen Sensor (Rear) Heater Circuit High
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0053: Heated Oxygen Sensor Heater (Front) Resistance
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other monitor and Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0068: Mass Airflow Sensor Plausibility
- DTC P0069: Abnormal Correlation Between Manifold Absolute Pressure Sensor And Barometric Pressure Sensor
- DTC P0096: Intake Air Temperature Circuit Range/Performance Problem (Sensor 2)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0097: Intake Air Temperature Circuit Low Input (Sensor 2)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0098: Intake Air Temperature Circuit High Input (Sensor 2)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0101: Mass Airflow Circuit Range/Performance Problem
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC SET CONDITIONS
- DTC SET CONDITIONS
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0102: Mass Airflow Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0103: Mass Airflow Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0106: Manifold Absolute Pressure Circuit Range/Performance Problem
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC SET CONDITIONS
- DTC SET CONDITIONS
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0107: Manifold Absolute Pressure Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0108: Manifold Absolute Pressure Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0111: Intake Air Temperature Circuit Range/Performance Problem (Sensor 1)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0112: Intake Air Temperature Circuit Low Input (Sensor 1)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0113: Intake Air Temperature Circuit High Input (Sensor 1)
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0116: Engine Coolant Temperature Circuit Range/Performance Problem
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0117: Engine Coolant Temperature Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0118: Engine Coolant Temperature Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0121: Throttle Position Sensor (Main) Plausibility
- DTC P0122: Throttle Position Sensor (Main) Circuit Low Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0123: Throttle Position Sensor (Main) Circuit High Input
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC Set Conditions
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0125: Insufficient Coolant Temperature For Closed Loop Fuel Control
- Notes
- Circuit Operation
- Technical Description
- Descriptions Of Monitor Methods
- Monitor Execution
- MONITOR EXECUTION CONDITIONS (Other Monitor And Sensor)
- DTC SET CONDITIONS
- DTC SET CONDITIONS
- Fail-Safe And Backup Function
- OBD-II Drive Cycle Pattern
- TROUBLESHOOTING HINTS (The Most Likely Causes For This Code To Be Set Are:)
- Diagnosis
- DTC P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
- DTC P0010: Intake Engine Oil Control Valve Circuit