Adjustment Snap Ring And Spacers
WARNING: This page is about a different car, the 2012 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.
Snap ring (For adjustment of input shaft rear bearing end play)
SNAP RING THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 1.23 (0.0484) | 1.55 (0.0610) |
| 1.27 (0.0500) | 1.59 (0.0626) |
| 1.31 (0.0516) | 1.63 (0.0642) |
| 1.35 (0.0531) | 1.67 (0.0657) |
| 1.39 (0.0547) | 1.71 (0.0673) |
| 1.43 (0.0563) | 1.75 (0.0689) |
| 1.47 (0.0579) | 1.79 (0.0705) |
| 1.51 (0.0594) |
Spacer (For adjustment of input shaft end play)
SPACER THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
| 1.04 (0.0409) | 1.46 (0.0575) |
| 1.07 (0.0421) | 1.49 (0.0587) |
| 1.10 (0.0433) | 1.52 (0.0598) |
| 1.13 (0.0445) | 1.55 (0.0610) |
| 1.16 (0.0457) | 1.58 (0.0622) |
| 1.19 (0.0469) | 1.61 (0.0634) |
| 1.22 (0.0480) | 1.64 (0.0646) |
| 1.25 (0.0492) | 1.67 (0.0657) |
| 1.28 (0.0504) | 1.70 (0.0669) |
| 1.31 (0.0516) | 1.73 (0.0681) |
| 1.34 (0.0528) | 1.76 (0.0693) |
| 1.37 (0.0539) | 1.79 (0.0705) |
| 1.40 (0.0551) | 1.82 (0.0717) |
| 1.43 (0.0563) |
Snap ring (For adjustment of output shaft 3rd speed gear end play)
SNAP RING THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 2.23 (0.0878) | 2.47 (0.0972) |
| 2.27 (0.0894) | 2.51 (0.0988) |
| 2.31 (0.0909) | 2.55 (0.1004) |
| 2.35 (0.0925) | 2.59 (0.1020) |
| 2.39 (0.0941) | 2.63 (0.1035) |
| 2.43 (0.0957) | 2.67 (0.1051) |
Snap ring (For adjustment of output shaft rear bearing end play)
SNAP RING THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 1.31 (0.0561) | 1.55 (0.0610) |
| 1.35 (0.0531) | 1.59 (0.0626) |
| 1.39 (0.0547) | 1.63 (0.0642) |
| 1.43 (0.0563) | 1.67 (0.0657) |
| 1.47 (0.0579) | 1.71 (0.0673) |
| 1.51 (0.0594) |
Spacer (For adjustment of output shaft end play)
SPACER THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 1.19 (0.0469) | 1.52 (0.0598) |
| 1.22 (0.0480) | 1.55 (0.0610) |
| 1.25 (0.0492) | 1.58 (0.0622) |
| 1.28 (0.0504) | 1.61 (0.0634) |
| 1.31 (0.0516) | 1.64 (0.0646) |
| 1.34 (0.0528) | 1.67 (0.0657) |
| 1.37 (0.0539) | 1.70 (0.0669) |
| 1.40 (0.0551) | 1.73 (0.0681) |
| 1.43 (0.0563) | 1.76 (0.0693) |
| 1.46 (0.0575) | 1.79 (0.0705) |
| 1.49 (0.0587) |
Snap ring (For adjustment of reverse idler gear thrust washer end play)
SNAP RING THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 1.77 (0.0697) | 2.12 (0.0835) |
| 1.82 (0.0717) | 2.17 (0.0854) |
| 1.87 (0.0736) | 2.22 (0.0874) |
| 1.92 (0.0756) | 2.27 (0.0894) |
| 1.97 (0.0776) | 2.32 (0.0913) |
| 2.02 (0.0795) | 2.37 (0.0933) |
| 2.07 (0.0815) | 2.42 (0.0953) |
Spacer (For adjustment of center differential case end play)
SPACER THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
|---|---|
| 1.07 (0.0421) | 1.34 (0.0528) |
| 1.10 (0.0433) | 1.37 (0.0539) |
| 1.13 (0.0445) | 1.40 (0.0551) |
| 1.16 (0.0457) | 1.43 (0.0563) |
| 1.19 (0.0469) | 1.46 (0.0575) |
| 1.22 (0.0480) | 1.49 (0.0587) |
| 1.25 (0.0492) | 1.52 (0.0598) |
| 1.28 (0.0504) | 1.55 (0.0610) |
| 1.31 (0.0516) |
Spacer (For adjustment of center differential case pinion backlash)
SPACER THICKNESS SPECIFICATIONS
| Thickness mm (in) | Thickness mm (in) |
| 1.4 (0.055) | 1.7 (0.067) |
| 1.5 (0.059) | 1.8 (0.071) |
| 1.6 (0.063) | 1.9 (0.075) |