LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2010 >> Lancer ES, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 37 (Supplemental Restraint System (SRS) - Lancer Evolution) >> SRS Air Bag Diagnosis >> Data List Reference Table >> Data List Output

Data List Output

WARNING: This page is about a different car, the 2012 Mitsubishi Lancer. However, it is still accessible from the selected car via links, so may be relevant.

The following items can be read by the scan tool from the SRS-ECU input data.

DATA LIST

Item No. Display on scan tool Check conditions Normal conditions
01 SRS warning light illumination request
  • Ignition switch: ON
  • After warning lamp pre-check
 OFF
  • Ignition switch: ON
  • During warning lamp pre-check
 ON
02 Pass. SRS light "ON" request
  • Ignition switch: ON
  • After warning light pre-check
 OFF
  • Ignition switch: ON
  • During warning light pre-check
 ON
04 Passenger's seatbelt switch
  • Ignition switch: ON
  • After warning light pre-check
  • Wear the passenger seatbelt.
 Fastened
  • Ignition switch: ON
  • After warning light pre-check
  • Undo the passenger seatbelt.
 Unfastened
05 Passenger seat airbag ignition
  • Ignition switch: ON
  • After warning light pre-check
  • Apply a load to the passenger seat.
 Permission
  • Ignition switch: ON
  • After warning light pre-check
  • Undo a load from a passenger seat.
 Prohibition

The following items can be read by the scan tool from the occupant classification-ECU input data.

DATA LIST

Item No. Display on scan tool Check conditions Normal conditions
01 Passenger weight Apply a load to the passenger seat. -2048 Kg (4515 lb) to 2048 Kg (4515 lb)
02 Dr seat position sensor current Slide the seat the back-end to the front-position. 0 to 1, 700 mA
03 Dr seat position sensor voltage Slide the seat the back-end to the front-position. 0 to 5, 000 mV
07 Dr seat position sensor status Slide the seat the back-end to the front-position. Not Frontal Zone/Frontal Zone/Undetermined/No Dr STPS/No Pa STPS/Seat sensor DTC
08 occupant classification status Apply a load to the passenger seat. Empty/RFIS(1)/Child/More 5th%/Less 5th%/Undermined
10 Battery voltage Always 6.5 to 16 V
21 Pa seat weight sensor 1 RR Apply a load to the passenger seat. -2048 Kg (4515 lb) to 2048 Kg (4515 Ib)
22 Pa seat weight sensor 1 RR volt Apply a load to the passenger seat. 0 to 5, 000 mV
23 Pa seat weight sensor 2 RF Apply a load to the passenger seat. -2048 Kg (4515 Ib) to 2048 Kg (4515 Ib)
24 Pa seat weight sensor 2 RF volt Apply a load to the passenger seat. 0 to 5, 000 mV
25 Pa seat weight sensor 3 LF Apply a load to the passenger seat. -2048 Kg (4515 lb) to 2048 Kg (4515 lb)
26 Pa seat weight sensor 3 LF volt Apply a load to the passenger seat. 0 to 5, 000 mV
27 Pa seat weight sensor 4 LR Apply a load to the passenger seat. -2048 Kg (4515 lb) to 2048 Kg (4515 lb)
28 Pa seat weight sensor 4 LR volt Apply a load to the passenger seat. 0 to 5, 000 mV
30 VIN Information Always -
NOTE:
(1) Radio Frequency Integrated Circuit
scientia non olet · About LEMON Manuals