LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2008 >> Outlander LS, FWD >> Repair and Diagnosis >> Electrical >> Motors, Switches, Relays >> Chassis Electrical - 1 Of 5 >> Combination Meter >> Service Reminder Function Set >> How To Set By Operating The Scan >> How To Operate The Scan Tool MB991958

How To Operate The Scan Tool MB991958

CAUTION: Before setting, if the combination meter does not start measuring the elapsed time, turn the ignition switch to the ON position while pressing the meter information switch to start a measurement.
  1. Connect the scan tool MB991958 to the data link connector.
  2. Start the M.U.T.-III system on the PC and turn the ignition switch to the "ON" position.
  3. Select "Meter" on the "System Select" screen, and press the "OK" button.
  4. Select "Special Function" on the next screen.
  5. Select "Service Reminder" on the "Special function" screen.
  6. Select the function to be executed from "Function List".
  1. REMINDER RESET (INDICATOR OFF) 
    CAUTION:
    • Be careful not to execute "1 Reminder reset (Indicator off)" again after erasing the service reminder warning indicator which is currently output, because the next warning period will be cancelled.
    • If the next warning period is cancelled by mistake, the cancelled warning period can be restored by executing "5 Periodic reminder schedule set" to set a schedule different from the current one once, and then returning it to the previous schedule.

    The service reminder warning indicator which is currently output can be cancelled.

    NOTE: In addition to the operation of the scan tool MB991958, the service reminder warning indicator can be cancelled by operating the meter information switch on the combination meter. Refer to RELATIONSHIP BETWEEN THE ELAPSED MONTHS AND THE ELAPSED DAYS WHICH ARE USED BY THE SERVICE REMINDER FUNCTION  .
    1. On the "Service Reminder" screen, select "1 Reminder reset (Indicator off)".
      NOTE: The screen indicates that the warning period (Nos. 1 and 2 in the data list) is "0 mile". and "0 month".
    2. Press the "OK" button.
      Fig 2: Screen Display - Service Reminder
      G05396752Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    3. The current warning indicator is cancelled, and the next warning period is displayed.
      NOTE: The screen indicates that the warning period (Nos. 1 and 2 in the data list) is "7, 500 km" and "6 month".
  2. NEXT SCHEDULE REMINDER CANCEL 
    CAUTION: If the next warning period is cancelled by mistake, the cancelled warning period can be restored by executing "5 Periodic reminder schedule set" to set a schedule different from the current one once, and then returning it to the previous schedule.
    Fig 3: Screen Display - Warning Period
    G05385258Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

    The next warning period is cancelled, and its following warning period can be set.

    1. On the "Service Reminder" screen, select "2 Next schedule reminder cancel".
      NOTE: The screen indicates that the warning period (Nos. 1 and 2 in the data list) is "1, 000 mile" and "1 month".
    2. Press the "OK" button.
      Fig 4: Screen Display - Service Reminder
      G05385259Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    3. The next warning period is cancelled, and its following warning period is set.
      NOTE: The screen indicates that the warning period (Nos. 1 and 2 in the data list) is changed to "8, 500 km" and "7 month".
  3. EXTRA REMINDER SETTING 

    In addition to the current warning period, the temporary service reminder warning period can be set.

    Fig 5: Screen Display - Warning Period
    G05385260Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. On the "Service Reminder" screen, select "3 Extra reminder setting".
      NOTE: The screen indicates that the temporary warning period (Nos. 4 and 5 in the data list) has not been set.
      Fig 6: Screen Display - Service Reminder
      G05385261Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set the temporary warning period (distance or month) of the "Set value".
      NOTE: Either input of distance or month can execute the setting.
    3. Press the "OK" button.
      Fig 7: Screen Display - Warning Period
      G05385262Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    4. The temporary warning period is set.
      NOTE: The screen indicates that "2 month" has been added to the temporary warning period (No. 5 in the data list). (The distance of No. 4 in the data list has not been set).
  4. EXTRA REMINDER CANCEL 

    The temporary service reminder warning period which has been set can be cancelled.

    Fig 8: Screen Display - Warning Period
    G05385263Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. On the "Service Reminder" screen, select "4 Extra reminder cancel".
      NOTE: The screen indicates that "3000 mile" and "2 month" have been set to the temporary warning period (Nos. 4 and 5 in the data list).
    2. Press the "OK" button.
      Fig 9: Screen Display - Service Reminder
      G05385264Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    3. The temporary warning period is cancelled.
      NOTE: The screen indicates that the temporary warning period (Nos. 4 and 5 in the data list) has been cancelled.
  5. PERIODIC REMINDER SCHEDULE SET 

    The service reminder schedule can be changed.

    NOTE: In addition to the operation of the scan tool MB991958, the schedule can be changed by operating the meter information switch on the combination meter. Refer to.
    Fig 10: Screen Display - Warning Period
    G05385265Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. On the "Service Reminder" screen, select "5 Periodic reminder schedule set".
      NOTE: The screen indicates that the current schedule (No. 7 in the data list) has been set to "NAS 10".
      Fig 11: Screen Display - Service Reminder
      G05396761Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. Set the schedule to be changed from "Set value".
    3. Press the "OK" button.
      Fig 12: Screen Display - Set Value
      G05396762Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    4. The schedule is changed.
      NOTE: The screen indicates that the current schedule (No. 7 in the data list) has been changed to "NAS 11".
  6. INTEGRATED VALUE ADJUSTMENT 

    At the combination meter replacement or for the vehicle with its battery being removed for a long period (15 days or more), this adjustment is used to reset the mileage and elapsed days for check warning.

    Fig 13: Screen Display - NAS 11
    G05396763Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    1. On the "Service Reminder" screen, select "6 Integrated value adjustment".
      NOTE: The screen indicates that the current mileage and elapsed days (Nos. 8 and 9 in the data list) are "26 mile" and "0 day".
      Fig 14: Screen Display - Service Reminder
      G05385269Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    2. To "Set value," input the mileage and elapsed days to be reset.
      NOTE: Always input both the mileage and elapsed days.
    3. Press the "OK" button.
      Fig 15: Screen Display - Set Value
      G05385270Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
    4. The mileage and elapsed days are changed. The combination meter automatically recalculates the distance and days to the nearest next check from the settings of mileage and elapsed days for check warning, and then displays them in "Data List".
      NOTE:
      • The screen indicates that the current mileage and elapsed days (Nos. 8 and 9 in the data list) have been changed to "100 mile" and "30 day".
        Fig 16: Screen Display - Data List
        G05385271Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
      • Set the elapsed days for check warning to "0 day" by the above resetting method, thereby the timer is reset indirectly.
  7. OPTIONAL INT SCHEDULE SETTING 
CAUTION: If the current schedule is set to the "Optional INT" by executing "5. Periodic reminder schedule set," the "set value" cannot be input. Therefore, set it to the schedule other than the "Optional INT" once, and then execute "7. Optional INT schedule setting".

In addition to the existing schedule, the optional service reminder schedule can be set.

  1. On the "Service Reminder" screen, select "7 Optional INT schedule setting".
    NOTE: The screen indicates that the optional schedule (Nos. 12 and 13 in the data list) has not been set.
    Fig 17: Screen Display - Service Reminder
    G05385272Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  2. Set the optional schedule (distance or month) of the "Set value".
    NOTE: Either input of distance or month can execute the setting.
  3. Press the "OK" button.
    Fig 18: Screen Display - Set Value
    G05385273Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
  4. The optional schedule is set. The set schedule becomes effective by executing "5 Periodic reminder schedule set" and setting the schedule to "Optional INT".
    NOTE: The screen indicates that "2 month" has been added to the optional schedule (No. 13 in the data list). (The distance of No. 12 in the data list has not been set).
    Fig 19: Screen Display - Data List
    G05385274Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
scientia non olet · About LEMON Manuals