33 31 011 Replacing rear axle support (Countryman models with FWD)

Preliminary work needed: 

• Remove REAR WHEELS .
• Remove exhaust system.
• Remove TANK COVER on left and right.

Removal: 

Press brake pedal down to floor and secure with pedal support.

Courtesy of BMW OF NORTH AMERICA, INC.

Remove heat shield (1).

Courtesy of BMW OF NORTH AMERICA, INC.

• Remove all wishbones. Refer to 33 32 086 REMOVING AND INSTALLING/REPLACING BOTTOM LEFT WISHBONE (COUNTRYMAN MODELS WITH FWD) , 33 32 087 REMOVING AND INSTALLING/REPLACING BOTTOM RIGHT WISHBONE (COUNTRYMAN 2017-2023, EXCEPT PHEV) , 33 32 076 REMOVING AND INSTALLING/REPLACING TOP LEFT WISHBONE (COUNTRYMAN MODELS WITH FWD)  and 33 32 077 REMOVING AND INSTALLING/REPLACING TOP RIGHT WISHBONE (Countryman 2017-2023, except PHEV) .

Release hollow nut (2).

Detach brake hose (1) on left and right from brake line.

Courtesy of BMW OF NORTH AMERICA, INC.

Only for rear ride height sensor:

Disconnect connector (1).

Release screw (2).

Remove ride height sensor.

Courtesy of BMW OF NORTH AMERICA, INC.

Support rear axle support (1) with workshop jack (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) from rear axle support (2).

Lower rear axle support by approx. 10 cm.

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1) from anti-roll bar (2).

Courtesy of BMW OF NORTH AMERICA, INC.

Remove rear axle support.

Courtesy of BMW OF NORTH AMERICA, INC.

Installation: 

Position the rear axle support on the vehicle with the universal lifter.

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down anti-roll bar (2) with screws (1) on rear axle support.

Tightening torque 33 55 3AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down rear axle support (2) with screws (1) on vehicle.

Tightening torque 33 31 1AZ .

Lower workshop jack and put away.

Courtesy of BMW OF NORTH AMERICA, INC.

Only for rear ride height sensor:

Position ride height sensor.

Tighten screw (2).

Tightening torque 37 14 3AZ .

Connect the connector (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Connect brake hose (1) on left and right to brake line.

Tighten down hollow nut (2).

Tightening torque 34 32 1AZ .

Courtesy of BMW OF NORTH AMERICA, INC.

• Install all wishbones. Refer to 33 32 086 REMOVING AND INSTALLING/REPLACING BOTTOM LEFT WISHBONE (COUNTRYMAN MODELS WITH FWD) , 33 32 087 REMOVING AND INSTALLING/REPLACING BOTTOM RIGHT WISHBONE (COUNTRYMAN 2017-2023, EXCEPT PHEV) , 33 32 076 REMOVING AND INSTALLING/REPLACING TOP LEFT WISHBONE (COUNTRYMAN MODELS WITH FWD)  and 33 32 077 REMOVING AND INSTALLING/REPLACING TOP RIGHT WISHBONE (COUNTRYMAN 2017-2023, EXCEPT PHEV) .

Install heat shield (1).

Courtesy of BMW OF NORTH AMERICA, INC.

Release pedal support.

Courtesy of BMW OF NORTH AMERICA, INC.

Required follow-up work: 

• VENTING BRAKE SYSTEM .
• Install TANK COVER on left and right.
• Install exhaust system.
• Install REAR WHEELS .
• Perform wheel alignment. Refer to 32 00 150 KDS CHASSIS/WHEEL ALIGNMENT CHECK WITH VEHICLE LOAD UP TO DESIGN POSITION (COUNTRYMAN 2017-2023, EXCEPT PHEV) or 32 00 155 KINEMATICS DIAGNOSIS SYSTEM WHEEL ALIGNMENT WITH RIDE HEIGHT MEASUREMENT WITHOUT LOADING THE VEHICLE (Countryman 2017-2023, except PHEV) .