REP-TAT-P-3610-02 Mounting the wheel

Follow-up work

Reset the RDC

Clean the contact surfaces between the brake disc and the wheel rim

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The contact surface between the brake disc and the wheel rim must be clean and free from oil and grease. There is otherwise a risk of the wheel becoming loose at a later time.

Remove dirt, grease residues and corrosion from the contact surface with a drill and the special tool 2344 011 .

Do not operate special tool 2 344 011 with an impact screwdriver.

Degrease contact surfaces.

Consumable
Universal cleaner	20 l, Canister	83192360981

Courtesy of BMW OF NORTH AMERICA, INC.

If there are grease deposits in the area of the wheel bolt holes, remove and clean the brake disc.
Remove dirt, grease residues and corrosion from the contact surface with a drill and the special tool 2 344 011 .

Do not operate special tool 2 344 011 with an impact screwdriver.

Degrease contact surfaces.

Courtesy of BMW OF NORTH AMERICA, INC.

Consumable
Universal cleaner	20 l, Canister	83192360981

Check that the mounting bolt (1) for the brake disc is securely seated.

Die mounting bolt (1) for the brake disc may not on the contact surface (2) between the brake disc and the wheel rim.

TIGHTENING TORQUE SPECIFICATION

Brake disc to front wheel hub
M8
	tightening torque
	16 Nm

TIGHTENING TORQUE SPECIFICATION

Brake disc to rear wheel hub
M8
	tightening torque
	16 Nm

Thinly grease the wheel centering (1) in the wheel rim.

Courtesy of BMW OF NORTH AMERICA, INC.

Consumable
Brake block paste * TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only.	3 g, Bag	83192158851
	100 g, Tube	83192158852
	5 g, TU*	83230140233

Coat the wheel hubs at the front and rear in area (1) with a thin layer of grease to protect them from corrosion.

Courtesy of BMW OF NORTH AMERICA, INC.

Consumable
Brake block paste * TU = Trade Unit. TU numbers cannot be ordered! For invoicing purposes only.	3g, Bag	83192158851
	100 g, Tube	83192158852
	5 g, TU*	83230140233

Check

Check lug bolts for wear.

Courtesy of BMW OF NORTH AMERICA, INC.

Result

» Put (> 30%) of the bearing surface (1) of the taper that shows silver wear on the screw head.

Measure

Replace lug bolts.

Parts: Wheel bolts

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
Never use an impact screwdriver or electric screwdriver to apply and tighten the lug bolts.
The rim must rest evenly against the brake disc.
In the case of non-original BMW lug bolts/wheel rims, it may be necessary to retighten the lug bolts on user account of setting properties (refer to the documentation from the aftermarktet manufacturer).
Do not apply oil to new lug bolts.

Clean the lug bolts (arrows).
Check lug bolts (arrows) and threads for damage, replace the lug bolts if necessary.
Replace corroded lug bolts (arrows).

Parts: Lug bolts

Screw in lug bolts (arrows) crosswise by hand and tighten hand-tight to center the wheel rim.
Use the torque wrench to tighten the lug bolts (arrow) crosswise.
Retighten all lug bolts (arrow) crosswise to check.

TIGHTENING TORQUE SPECIFICATION

Lug bolts
M14/SW17 Screw in wheel bolts and evenly tighten crosswise by hand in order to center the wheel rim.
Tighten lug bolts to the prescribed tightening torque with a calibrated torque wrench in a crosswise sequence.
Check all the lug bolts in the same order or retighten to the prescribed tightening torque again.
	tightening torque
	140 Nm
	Check 140 Nm