52 13 402 Replacing seat cover for driver's seat (normal/manual)

WARNING: This page is about a different car, the 2019 MINI Cooper, 2018 MINI Cooper, 2017 MINI Cooper, 2016 MINI Cooper, and 2015 MINI Cooper. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

52 0 050

WARNING: Injury hazard!
The seat frame has very sharp edges that can cause injuries from cuts.
Exercise extreme caution and wear hand protection as required when carrying out any repair work in the area of the seat frame.

IMPORTANT: Risk of damage on sharp-edged seat mechanism.
Guide all cables carefully through seat and backrest mechanism.
Make sure cable is routed without kinks and tension.
Make sure plug connections are correctly locked.
Make sure connectors are correctly seated in detents.

IMPORTANT:

Microencapsulated screws must be coated with Loctite if they are to be reused
Screw connection must be completed within 20 min. (start of harden)
Microencapsulated screws must not be retightened.

Thread of nut must be cleaned beforehand in event of repeated use

Preliminary work needed:

Remove DRIVER'S SEAT .
Remove INNER COVER
Remove OUTER COVER

Removal:

Use of the universal seat mount is recommended for carrying out professional repairs.

Fig 1: Front Seat

Courtesy of BMW OF NORTH AMERICA, INC.

Shift the backrest into an upright position.

Release left and right screws (4).

Completely remove the backrest (5) to the top.

If necessary, feed out cable and set aside backrest.

Fig 2: Removing Backrest To Top

Courtesy of BMW OF NORTH AMERICA, INC.

Unhook welt (1).

Version with seat heating only:

Unlock and disconnect connector (2).

Feed out cable.

IMPORTANT: Feed the wiring harness carefully through the seat and backrest mechanism as the edges of the frame can be sharp.

Fig 3: Locating Seat Connector

Courtesy of BMW OF NORTH AMERICA, INC.

Loosen clips (1) on the left and right side.

Fig 4: Loosening Clips On Left And Right Side

Courtesy of BMW OF NORTH AMERICA, INC.

Detach all-round piping (1) and remove the seat cover (2) with the facing.

If necessary, feed out cable.

Fig 5: Locating Seat Cover With Facing

Courtesy of BMW OF NORTH AMERICA, INC.

Release all clamps.

Remove seat cover from upholstery.

IMPORTANT: Remove all remnants of clamps from seat cover and upholstery.

Fig 6: Removing Remnants Of Clamps From Seat Cover And Upholstery

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Position seat cover.

Bend new clamps (2) with special tool 52 0 050.

Upholstery
Clamp
Trim wire in upholstery
Trim wire in cover
Seat cover

Fig 7: Bending New Clamps With Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Parts: Replace clamps.

If necessary, feed in cable.

Place the seat cover (2) with the facing and attach all-round piping (1).

Fig 8: Locating Seat Cover With Facing

Courtesy of BMW OF NORTH AMERICA, INC.

Install clips (1) on the left and right side.

Fig 9: Loosening Clips On Left And Right Side

Courtesy of BMW OF NORTH AMERICA, INC.

Attach welt (1).

Version with seat heating only:

Connect connector (2).

IMPORTANT: Feed the wiring harness carefully through the seat and backrest mechanism as the edges of the frame can be sharp.

Fig 10: Locating Seat Connector

Courtesy of BMW OF NORTH AMERICA, INC.

Install backrest (5).

If necessary, feed in cable.

Tighten screws (4) on left and right.

Tightening torque 52 10 2AZ .

Fig 11: Removing Backrest To Top

Courtesy of BMW OF NORTH AMERICA, INC.