41 11 043 Front Left Engine Support Section Replacement

WARNING: This page is about a different car, the 2010 BMW 535xi, 2009 BMW 535xi, and 2008 BMW 535xi. However, it is still accessible from the selected car via links, so may be relevant.

Read contents of BODY, GENERAL .

The reduced-weight aluminum front end structure (GRAV) is used on this vehicle.

Observe relevant procedures in BODY, GENERAL .

Place vehicle on straightening bench.

Following new body parts are required :

Engine carrier, front
Support carrier, bulkhead, outer
Reinforcement bracket, front, spring support
Reinforcement bracket, rear, spring support
Extension, engine carrier

The engine carrier is supplied with longer bolts for the E60 and E61. The bolts do not have to be shortened.

Fig 1: Support Carrier, Bulkhead, Outer And Engine Carrier, Front

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Use the mouthpiece (steel or plastic) with 10 mm inside diameter in the following work step to extract the rivets in areas (1) and (2). Using the plastic mouthpiece with 14 mm inside diameter will result in damage to the wheel arch!

Open rivet joints in areas (1) to (3).

Open EMC weld seam in area (3).

Installation:

Use 8 rivets (size 13) in areas (1).

Use 6 rivets (size 13) in areas (2).

Use 4 rivets (size 13) in areas (3).

Fig 2: Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Use 2 EMC screws in each case (4 x in total) in areas (1) and (2).

Fig 3: EMC Screws Areas

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Right side only:

Open rivet joints in areas (1).

Installation:

Use 2 rivets (size 13) in areas (1).

Fig 4: Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Engine carrier has been blanked out for purposes of clarity.
Spot-drill rivets in areas (1) and (2) from protruding rear side or grind and punch through.

Installation:

Use 5 rivets (size 13) in areas (1).

Use 2 rivets (size 13) in area (2).

Fig 5: Spot-Drill Rivets Areas From Protruding Rear Side Or Grind

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) to (3).

Installation:

Use 3 rivets (size 13) in area (1).

Use 4 rivets (size 13) in area (2).

Use 3 rivets (size 13) in area (3).

Fig 6: Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Spot-drill rivets in area (1) from protruding rear side or grind and punch through.

Fig 7: Spot-Drill Rivets Area From Protruding Rear Side Or Grind

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) to (3).

Installation:

Use 5 rivets (size 13) in area (1).

Use 4 rivets (size 13) in area (2).

Use 3 rivets (size 13) in area (3).

Use 4 rivets (size 13) in area (4).

Use 7 rivets (size 13) in area (5).

Fig 8: Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) and (2).

As a rule, part of the punch rivet remains in the rear engine carrier in area (2). Do not drill out remnants. Set blind rivets next to punch rivets.

Open weld joint in area (1).

Installation:

Use 4 rivets (size 13) in area (1).

Use 5 rivets (size 13) in area (2).

Use 6 rivets (size 13) in area (3).

Install 2 EMC screws in area (1).

Fig 9: Weld Joint Area

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in area (1).

Installation:

Use 3 rivets (size 13) in area (1).

Use 6 rivets (size 13) in area (2).

Use 1 rivet (size 13) in area (3).

Install 2 EMC screws in area (2).

Drill holes for rivets.

Fig 10: Rivet Joints Area

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Use 1 rivet (size 15) in area (1).

Fig 11: Rivet Joints Area

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) and (2).

As a rule, part of the punch rivet remains in the rear engine carrier in area (2). Do not drill out remnants. Set blind rivets next to punch rivets.

Open weld joint in area (3).

Installation:

Use 2 rivets (size 13) in area (1).

Install 2 EMC screws in area (1).

Use 7 rivets (size 13) in area (2).

Apply as much adhesive in area (2) that the adhesive emerges from the flange during riveting.

Fig 12: Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Spot-drill rivets in area (1) from protruding rear side or grind and punch through.

Installation:

Use 2 rivets (size 13) in area (1).

Set rivets from inside.

Fig 13: Spot-Drill Rivets Area From Protruding Rear Side Or Grind

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Use 6 rivets (size 13) in areas (1).

For reasons of accessibility, bond and rivet retaining brackets in areas (1) to engine carrier first after adjusting to fit.

Bond in area (2) only.

Fig 14: Rivets Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Preparation of new part:

Shorten new part in area (1) to a length of 50 mm by 7 mm.

Measurement a = 35 mm

Fig 15: New Part Area

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Bend open bulkhead support carrier (2) slightly in area (1).

Adjust all new parts to fit with straightening attachment or universal mount. Drill holes for rivets.

Bond engine carrier first and then rivet.

Slide engine carrier extension in direction of arrow underneath bulkhead support carrier (2).

Bond new part.

Rivet new part.

Align bulkhead support carrier (2) in area (1) until flush.

Use 2 rivets (size 13) in area (1).

Install 2 EMC screws in area (1).

Fig 16: Bulkhead Support Carrier And Area

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

AWD only:

After painting on both sides of car, stick zinc foil (1) to center bolting point (2) of front axle carrier.

Fig 17: Zinc Foil And Centre Bolting Point Of Front Axle Carrier

Courtesy of BMW OF NORTH AMERICA, INC.