41 14 021 Front Left Wheel Arch Replacement

WARNING: This page is about a different car, the 2010 BMW 535xi, 2009 BMW 535xi, and 2008 BMW 535xi. However, it is still accessible from the selected car via links, so may be relevant.

Read contents of BODY, GENERAL .

The reduced-weight aluminium front end structure (GRAV) is used on this vehicle.

Observe relevant procedures in BODY, GENERAL .

Place vehicle on straightening bench.

Following new body parts are required:

Wheel arch, front

Fig 1: Identifying Wheel Arch, Front

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) to (3).

As a rule, part of the punch rivet remains in the engine carrier in areas (2) and (3). Drill out remnants.

Open EMC weld seam in area (1).

Installation:

Carry over hole pattern from engine carrier to new part in areas (1) to (3).

Use 4 rivets (size 13) in areas (1).

Use 6 rivets (size 13) in areas (2).

Use 8 rivets (size 15) in areas (3).

IMPORTANT: If a partial replacement has already been carried out on the engine carrier, rivets (size 15) must be used in areas (1).

If the engine carrier is replaced at the same time as the wheel arch, rivets (size 13) must be used in areas (3).

Use 2 EMC screws in areas (1).

Use 2 EMC screws in areas (3).

If an engine carrier partial replacement has been carried out, 2 EMC screws must also be used in areas (2).

Fig 2: Identifying Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Fig 3: Identifying EMC Screws Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Open rivet joints in areas (1) and (2).

As a rule, part of the punch rivet remains in the units compartment partition wall in areas (1) and (2). Drill out remnants.

Installation:

Carry over bores from units compartment partition wall to new part in area (2).

Use 3 rivets (size 13) in area (1).

Use 2 rivets (size 13) in area (2).

Fig 4: Identifying Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Right side only:
Open rivet joints in areas (1).

Installation:

Use 2 rivets (size 13) in areas (1).

Fig 5: Identifying Rivet Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Open weld joints in areas (1) and (2).

Open rivet joints in area (2).

Installation:

If necessary, replace brazed seams with MAG weld seams in area (1).

Use 2 rivets (size 13) in area (2).

Fig 6: Identifying Weld Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Open weld joints in areas (1).

Fig 7: Identifying Weld Joints Areas

Courtesy of BMW OF NORTH AMERICA, INC.

Open weld joints in area (1).

Mark severance cut according to measurement a and cut inside A-pillar.

Measurement a = 47 mm from center of bore.

Fig 8: Identifying Severance Cut According Mark To Measurement A And Cut Inside A-Pillar

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: When replacing right wheel arch:
Measurement a = 65 mm from center of bore.
Measurement b = 20 mm

Fig 9: Identifying Measurement Line Between Right Wheel Arch And Centre Of Bore

Courtesy of BMW OF NORTH AMERICA, INC.

Different riveting-down elements, depending on the equipment specification, must be mounted on the new component.

Required tools are featured on the Workshop Equipment Planning CD (WEP).

Preparation of new part:

Mark severance cut (1) according to vehicle. Cut outer metal sheet only.

Drill out metal sheet in areas (2).

Installation:

Adjust new part to fit with straightening attachment or universal mount.

Let parts overlap 10 mm at severance cut (1).

Weld new component from inside and outside over entire length (from outside if accessible).

Drill holes for rivets.

Bond new part.

Rivet new part.

Fig 10: Identifying Severance Cut Mark According To Vehicle

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Seal new component in area (1) with sealing compound.

Fig 11: Identifying New Component Seal Area

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

There is no bore hole (1) for the support bearing centering pin in the new component!

Prior to installing spring strut, remove support bearing centering pin.

Fig 12: Identifying Bore Hole

Courtesy of BMW OF NORTH AMERICA, INC.