36 10 300 Removing or Installing Front or Rear Wheel

WARNING: This page is about a different car, the 2008 BMW 760Li, 2007 BMW 760Li, and 2006 BMW 760Li. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

36 1 120
36 1 250
36 1 300

IMPORTANT:

Observe safety instructions on raising the vehicle . See 00..... LIFTING VEHICLE WITH A LIFTING PLATFORM

Follow instructions on initializing Run Flat Indicator (RPA). See 36 11 500 INITIALIZING RUN FLAT INDICATOR (RPA)

After completing installation, check again that all wheel bolts are tightened to specified torque.

For tightening torque, see 36 10 1AZ in 36 10 WHEELS

Observe the following procedure to prevent shift errors and imbalance:

Loosen wheel bolts.
Wheel positioned with valve facing down.
If several wheels are removed simultaneously, mark the installation locations of the wheels on the tires (e.g. with chalk).
Mark out wheel to wheel hub.
Mark out lockable wheel bolt in relation to wheel.
Release wheel bolts, remove wheel.

Fig 1: Locating Valve & Nut
Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Contact surfaces between:

brake disk and disk wheel,
brake disk and wheel hub,

must be free from grease.

Remove dirt, grease residues and corrosion from contact face (1) with a drill and special tool 36 1 250 . See 36 1 250 WHEEL HUB GRINDER

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver! See 36 1 250 WHEEL HUB GRINDER

NOTE:

Degrease contact face with universal cleaner, refer to BMW Parts Service.

If there are grease residues in the area of the wheel stud bore, the brake disk must be removed and cleaned. See 34 11 220 REMOVING AND INSTALLING/REPLACING BOTH FRONT BRAKE DISCS and 34 21 320 REMOVING AND INSTALLING OR REPLACING BOTH REAR BRAKE DISCS

Fig 2: Identifying Contact Face With Special Tool (36 1 250)

Courtesy of BMW OF NORTH AMERICA, INC.

Remove dirt, grease residues and corrosion from contact face (1) with a drill and special tool 36 1 250 . See 36 1 250 WHEEL HUB GRINDER

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver! See 36 1 250 WHEEL HUB GRINDER

NOTE: Degrease contact face with universal cleaner, refer to BMW Parts Service.

Fig 3: Identifying Brake Disc With Special Tool (36 1 250)

Courtesy of BMW OF NORTH AMERICA, INC.

Check brake disk retaining bolt (1) for secure seating.

IMPORTANT: Mounting bolt (1) must not under any circumstances protrude over contact surface (2) between brake disk and disk wheel.

Tightening torque brake disk retaining bolt:

For front axle tightening torque, see 34 11 1AZ in 34 11 FRONT BRAKE

For rear axle tightening torque, see 34 21 1AZ in 34 21 REAR BRAKE

Fig 4: Identifying Brake Disk Retaining Bolt & With Contact Surface

Courtesy of BMW OF NORTH AMERICA, INC.

Apply a thin coat of grease to wheel centering (1) in disk wheel.

NOTE: Refer to BMW Service Operating Fluids, see FRONT AXLE - OPERATING FLUIDS .

Fig 5: Identifying Wheel Centering In Disk Wheel

Courtesy of BMW OF NORTH AMERICA, INC.

Wheel studs with taper:

Wheel bolt - galvanized
Wheel bolt - black chrome plated
Wheel bolt - black chrome plated and lockable
Lockable wheel stud with adapter, black chrome-plated

NOTE: To release and tighten down lockable wheel stud, use a matching adapter from special tool 36 1 300 . See 36 1 300 SET OF WHEEL STUD ADAPTERS

Fig 6: Identifying Wheel Stud With Adapter

Courtesy of BMW OF NORTH AMERICA, INC.

Clean wheel bolts and check threads for damage, replace, if necessary.

Replace rusty wheel bolts.

IMPORTANT: Do not apply oil to new wheel bolts.

Before inserting, wipe threads and tapers of used wheel bolts with an oil cloth.

IMPORTANT:

You may use an impact or power screwdriver to insert the wheel bolts and join the wheel until a tightening torque of 20 Nm is obtained.

Do not under any circumstances use an impact or power screwdriver to tighten down the wheel bolts (in diagonal sequence); this must be done by hand.

Tighten down wheel bolts with a calibrated torque wrench to prescribed tightening torque.

For tightening torque, see 36 10 1AZ in 36 10 WHEELS

IMPORTANT: Disk wheel must rest uniformly against brake disk.

Fig 7: Tightening Down Wheel Bolts With Calibrated Torque Wrench

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE:

For wheels with Styling 90 wheel cover.

The wheel cover can be removed for cleaning and removal of foreign objects.

Fit special tool 36 1 120 (3) as shown on rim (1) (near valve). See 36 1 120 LEVER

Engage removal fork of special tool 36 1 120 (3) in wheel cover (2). See 36 1 120 LEVER

Pull off wheel cover (2) with handle of special tool 36 1 120 (3). See 36 1 120 LEVER

Fig 8: Identifying Rim With Wheel Cover

Courtesy of BMW OF NORTH AMERICA, INC.