24 00 Transmission In General
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2008 BMW 750i, 2008 BMW 750Li, 2007 BMW 750i, 2007 BMW 750Li, and 2006 BMW 750i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - TRANSMISSION IN GENERAL
| - | Type | Thread | Tightening specification | Measure |
|---|---|---|---|---|
| 1AZ Transmission to engine | - | - | - | - |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | - | 24 Nm |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M10 | - | 45 Nm |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M12 | - | 82 Nm |
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M8 | - | 21 Nm |
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M10 | - | 42 Nm |
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M12 | - | 72 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M6 | - | 9 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M8 | - | 22 Nm |
| Torx screws N62TU | GA6HP26Z | M8 | - | 19 Nm |
| Torx screws N62TU | GA6HP26Z | M10 | - | 38 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M12 | - | 73 Nm |
| Torx screws, steel N51/N52/N54/N47/N53/N43/N45K | GA6HP19Z/GA6L45R | M8 | - | 19 Nm |
| Torx screws, steel N51/N52/N54/N43/N47/N53/N52K | GA6HP19Z/GA6L45R | M12 | - | 66 Nm |
| 2AZ Transmission to engine N51/N52/N54/N53/N52K Aluminum screws are marked blue | GA6HP19Z/GA6L45R | - | Replace screws Jointing torque and angle of rotation must be observed without fail | - |
| - | GA6HP19Z/GA6L45R | M10x30 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z | M10x85 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 180-200° |
| - | GA6HP19Z | M12 | Jointing torque | 34 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z/GA6L45R | M12x76 | Jointing torque | 25 Nm |
| - | - | - | Torque angle | 130° |
| 3AZ Reinforcement shell to transmission/extension | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | - | 23 Nm |
| 4AZ Cover plate for transmission | GA6HP19Z | M6 | - | 9 Nm |
TIGHTENING TORQUE SPECIFICATION - TRANSMISSION IN GENERAL
| - | Type | Thread | Tightening specification | Measure |
|---|---|---|---|---|
| 1AZ Transmission to engine | - | - | - | - |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | - | 24 Nm |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M10 | - | 45 Nm |
| Hex screws | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M12 | - | 82 Nm |
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z 5S 325Z/A5S 440Z A5S 560Z/A5S 360R/A5S 390R | M8 | - | 21 Nm |
| Torx bolts | A4S 200R/A4S 270R A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z /A5S 560Z/A5S 360R/A5S 390R | M10 | - | 42 Nm |
| Torx bolts | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R | M12 | - | 72 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M6 | - | 9 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M8 | - | 22 Nm |
| Torx screws N62TU | GA6HP26Z | M8 | - | 19 Nm |
| Torx screws N62TU | GA6HP26Z | M10 | - | 38 Nm |
| Torx bolts | GA6HP19Z/GA6HP26Z | M12 | - | 73 Nm |
| Torx screws, steel N51/N52/N54/N47/N53/N43/N45K | GA6HP19Z/GA6L45R | M8 | - | 19 Nm |
| Torx screws, steel N51/N52/N54/N43/N47/N53/N52K | GA6HP19Z/GA6L45R | M12 | - | 66 Nm |
| 2AZ Transmission to engine N51/N52/N54/N53/N52K Aluminum screws are marked blue | GA6HP19Z/GA6L45R | - | Replace screws Jointing torque and angle of rotation must be observed without fail | - |
| - | GA6HP19Z/GA6L45R | M10x30 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z | M10x85 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 180-200° |
| - | GA6HP19Z | M12 | Jointing torque | 34 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z/GA6L45R | M12x76 | Jointing torque | 25 Nm |
| - | - | - | Torque angle | 130° |
| 3AZ Reinforcement shell to transmission/extension | A4S 200R/A4S 270R/A4S 310R/A5S 300J/A5S 310Z/A5S 325Z/A5S 440Z/A5S 560Z/A5S 360R/A5S 390R/GA6HP19Z/GA6HP26Z/GA6HP32Z | M8 | - | 23 Nm |
| 4AZ Cover plate for transmission | GA6HP19Z | M6 | - | 9 Nm |