51 61 Reinforcement, body
WARNING: This page does not describe the selected car, but rather 27 other vehicles, including the 2017 BMW M6, 2017 BMW 650i xDrive, 2017 BMW 650i, 2017 BMW 640i xDrive, and 2017 BMW 640i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - REINFORCEMENT, BODY
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Suspension cross-brace in engine compartment, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws | |
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F15/F16 | Renew screws | ||||
| Jointing torque | 25 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F25/F26 | M10x25 | Renew screws | |||
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 2AZ | Suspension cross-brace in engine compartment, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x25 | 56 Nm | |
| F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M10x47 | Renew screws | |||
| Jointing torque | 30 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 3AZ | Connection, rear, to carrier support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 28 Nm | ||
| 4AZ | Connection, front, to connection, rear | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 5AZ | Engine compartment lid catch | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8x20 | 11.8 Nm | |
| 6AZ | V-support to connection, front | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 7AZ | Air duct, lower, to vertical strut | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | 19 Nm | ||
| 8AZ | Air duct, lower, to carrier | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 9AZ | Air duct, upper, on lock support | F01/F02/F03/F04/F06/F07/F10/F11/F12/F13/F18 | M8 | 8 Nm | |
| 10AZ | Trailing link/V-strut on side member | F07/F11/F12/F13 | M12 | Renew screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 11AZ | Trailing link to compression strut, rear axle | F07/F11/F12 | M8 | 19 Nm | |
| 12AZ | Trailing link to cross reinforcement (rear end support) | F07/F11/F12 | M12 | Renew screws | |
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 13AZ | Cross reinforcement (support, rear end) to rear end | F07/F11/F12 | M10x22 | 38 Nm | |
| 14AZ | Cross reinforcement (support, rear end) to cross-member | F07/F11/F12 | M10 | 38 Nm | |
| 15AZ | Torsion struts/stiffening plate to front axle support | F01/F02/F03/F12 | M10 | Renew screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 16AZ | Rear trailing link | F10/F12 | M10x40 | Renew screws | |
| Jointing torque | 56 Nm | ||||
| Angle of rotation | 105 ° | ||||
| 17AZ | Rear trailing link | F10/F12 | M8x35 | Renew screws | |
| Jointing torque | 28 Nm | ||||
| Angle of rotation | 90 ° | ||||