36 10 300 Remove or install front or rear wheel

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2012 BMW 328xi, 2012 BMW 328i, 2011 BMW 328xi, 2011 BMW 328i, and 2010 BMW 328xi. However, it is still accessible from the selected car via links, so may be relevant.

IMPORTANT: Observe safety instructions on raising the vehicle with a lifting platform.

When fitting all four wheels (e.g. when changing from summer to winter wheels), check the tire inflation pressure.

To avoid tire damage, advise the customer to check the tire inflation pressures on a regular basis (see Owner's Handbook).

Follow instructions on initializing Run Flat Indicator See 3611503 RESETTING RDC (TYRE PRESSURE CONTROL) or 3611000 INITIALIZING RUN FLAT INDICATOR (RPA) (RPA).

After completing installation, check again that all wheel bolts are tightened to specified torque.

Tightening torque 36 10 1AZ .

Observe the following procedure to prevent shift errors and imbalance:

Loosen wheel bolts.
Wheel positioned with valve facing down.
If several wheels are simultaneously removed, mark installation location of wheels on tires (e.g. with a piece of chalk).
Mark out wheel to wheel hub.
Mark out lockable wheel bolt in relation to wheel.
Release wheel bolts, remove wheel.

Fig 1: Identifying Wheel Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: The following contact faces must be free from grease and clean:

between brake disc and disc wheel
between brake disc and wheel hub

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver!

Remove dirt, grease residues and corrosion from contact surface (1) with a drill and special tool 36 1 250 .

NOTE: Degrease contact surface with universal cleaner.

If there are grease residues in the area of the wheel bolt bore, the brake disc must be removed See 3411220 REMOVING AND INSTALLING/REPLACING BOTH FRONT BRAKE DISCS (BREMBO) ; 3411220 REMOVING AND INSTALLING OR REPLACING BOTH FRONT BRAKE DISCS or 3421320 REMOVING AND INSTALLING/RENEWING BOTH BRAKE DISCS and cleaned.

Fig 2: Identifying Brake Disc And Disc Wheel Contact Surface With Special Tool (36 1 250)

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver!

Remove dirt, grease residues and corrosion from contact surface (1) with a drill and special tool 36 1 250 .

NOTE: Degrease contact surface with universal cleaner.

Fig 3: Identifying Contact Surface With Special Tool 36 1 250

Courtesy of BMW OF NORTH AMERICA, INC.

Check brake disc retaining bolt (1) for secure seating.

IMPORTANT: Mounting bolt (1) must not under any circumstances protrude over contact surface (2) between brake disc and disc wheel.

Tightening torque brake disc retaining bolt:

FRONT AXLE 34 11 1AZ .

REAR AXLE 34 21 1AZ .

Fig 4: Identifying Brake Disc Mounting Bolt Position With Brake Disc And Disc Wheel Contact Surface

Courtesy of BMW OF NORTH AMERICA, INC.

Apply a thin coat of grease to wheel centering (1) in disc wheel.

Fig 5: Identifying Wheel Centering On Disc Wheel

Courtesy of BMW OF NORTH AMERICA, INC.

Wheel bolts with taper:

Wheel bolt - galvanized
Wheel bolt - black chrome plated
Wheel bolt - black chrome plated and lockable
Lockable wheel bolt with adapter, black chrome-plated

NOTE: To release and tighten down lockable wheel bolts, use a matching adapter from special tool 36 1 300 .

Fig 6: Identifying Wheel Bolts With Taper

Courtesy of BMW OF NORTH AMERICA, INC.

Clean wheel bolts and check threads for damage, replace, if necessary.

Replace rusty wheel bolts.

IMPORTANT: Do not apply oil to wheel bolts.

IMPORTANT: Do not under any circumstances use an impact or power screwdriver to tighten down the wheel bolts (in diagonal sequence); this must be done by hand.

IMPORTANT: Disc wheel must rest uniformly against brake disc.

In the case of non-original BMW wheel studs/rims it may be necessary to retighten the wheel studs on account of settling properties (refer to manufacturer's documents).

Fit wheel bolts and evenly tighten crosswise by hand in order to center the disc wheel.

Tighten down wheel bolts in crosswise sequence with a calibrated torque wrench to prescribed tightening torque.

TIGHTENING TORQUE 36 10 1AZ .

Fig 7: Tightening Down Wheel Bolts Using Torque Wrench

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: For wheels with Styling 90 wheel cover.

The wheel cover can be removed for cleaning and removal of foreign objects.

Fit special tool 36 1 120 (3) as shown on rim (1) (near valve).

Engage removal fork of special tool 36 1 120 (3) in wheel cover (2).

Pull off wheel cover (2) with handle of special tool 36 1 120 (3).

Fig 8: Pulling Off Wheel Cover With Handle Of Special Tool (36 1 120)

Courtesy of BMW OF NORTH AMERICA, INC.