26 11 Propeller Shaft complete
WARNING: This page is about a different car, the 2012 BMW 328i, 2011 BMW 328i, 2010 BMW 328i, and 2009 BMW 328i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specifications | Dimension | |
|---|---|---|---|---|
| 4AZ Propeller shaft to drive flange (rear axle final drive) | ||||
| Finish Universal Joint: | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | 64 Nm | |
| Zinc Coated Shiny All Models with cross or CV joint |
Angle must be strictly adhered to | |||
| E83/E85/E86/E87/E90/E91/E92/E93/E81/E82/E88 | M10-10.9 With ribbed teeth | Assembly torque Rotation angle |
40 Nm 45° |
|
| E92 M3 | M10 Screw with Ribbed teeth |
Assembly torque Rotation angle |
20 Nm 90 ° |
|
| E46/E60/E61/E63/E64/E65/E66/E83/E85/E86/E81/E82/E87/E90/E91/E92/E93/E88/E84 | M10-10.9 | Assembly torque Rotation angle |
20 Nm 90° |
|
| E90/E91/E92/E93/E81/E87/E82/E83/E88/E84 | M12x55-10.9 | Assembly torque Rotation Angle |
55 Nm 90° |
|
| Nut with ribs | E85/M, E86/M | M10x46-10.9 | Replace screws and washers | 70 Nm |
| 5AZ Pivot fork piece to center propeller shaft bearing journal with Loctite (Version without sliding piece) | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | 97 Nm | ||
| 6AZ Centre mount to body | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E84/E88/E89 | 21 Nm | ||
| 7AZ Flexible disc to front axle differential | E53 | M10-10.9 | 60 Nm | |
| 8AZ Flexible disc on propeller shaft | E53 | M10-10.9 | 64 Nm | |
| 9AZ Front propeller shaft to transfer box/front axle differential ZNS screws and nuts, shiny zinc coating | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | |||
| E60/E61/E90/E91/E92/E84/E70/E71 | M8 | Jointing torque Angle of rotation |
20 Nm 45° |
|
| E46 | M10-10.9 | Jointing torque Angle of rotation |
20 Nm 45° |
|
| E53/E70/E71/E72 | M10-12.9 | Jointing torque Angle of rotation |
10 Nm 45° |
|
| E46 | M10x1.5 10.9 | Jointing torque Angle of rotation |
5 Nm 90 ° |
|
| Universal joint | E70/E71/E72/E83 | M10-10.9 | Jointing torque Angle of rotation |
40 Nm 45° |
TIGHTENING TORQUE SPECIFICATIONS - PROPELLER SHAFT. COMPLETE
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Flexible disc to propeller shaft and transmission output flange Steel propeller shaft | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 8.8 | 48 Nm | |
| E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 10.9 | 64 Nm | ||
| E31/E38/E39/E46 | M14 | 140 Nm | ||
| E32/E34/E36/E38/E39 | M12 8.8 | 81 Nm | ||
| E60/E61/E63/E64 | M12 8.8 | 90 Nm | ||
| E32/E34/E36/E38/E39/E46/E53/E85 | M12 10.9 | 100 Nm | ||
| E60/E61/E63/E64 | M12 10.9 | Jointing torque Torque angle |
55 Nm 90 ° |
|
| E39 (M5)/E36 (M3)/E46 (M3), | M12 10.9 | 115 Nm | ||
| E65 | M12 10.9 | 90 Nm | ||
| Flexible disc to transmission output flange | E46/E39/E60/With M57 | Screw with rolled-on washer only Jointing torque Torque angle |
50 Nm 90 ° |
|
| Flexible disc to transmission output flange | E65/E66/N73, M67 | Screw with rolled-on washer only Jointing torque Torque angle |
50 Nm 90 ° |
|
| E60/E61/E63/E64/E65/E66/E67 | M12 10.9 | Double-stage flexible disc Jointing torque Torque angle |
50 Nm 90 ° |
|
| Flexible disc on propeller shaft | E83 | M12 10.9 | Tighten via nut | 100 Nm |
| Flexible disc to transmission output flange | E83 | M12 10.9 | 90 Nm | |
| Aluminium propeller shaft: Flexible disc to transmission output flange | E39/E60 | M12 10.9 | 100 Nm | |
| Aluminium propeller shaft: Flexible disc on propeller shaft | E39/E60 | M12 10.9 | 90 Nm | |
| E60/E61/E63/E64 | M10 10.9 | 64 Nm | ||
| E60 | M12 8.8 | 90 Nm | ||
| E63 (N52) | M12 | 110 Nm | ||
| Flexible disc to transmission output flange ZNS screws and nuts Shiny zinc coating All versions | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | |||
| E60/E61/E63/E64/E85/E86/E87/E90/E91/E92/E93/E81/E82/E83/E84/E88/E89 | M10-10.9 | Jointing torque Torque angle |
20 Nm 90 ° |
|
| E46/E53/E60/E61/E63/E64/E65/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E83/E84/E88/E89 | M12-10.9 | Jointing torque Torque angle |
55 Nm 90 ° |
|
| E60/E61/E63/E64/E65 | M12-8.8 | Jointing torque Torque angle |
30 Nm 90 ° |
|
| E83 | M12-10.9 | Jointing torque Torque angle Screw with ribbed teeth + double stage flexible disc |
30 Nm 90 ° |
|
| 2AZ Coupling propeller shaft to transmission | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 | 60 Nm | |
| E32/E31 | M12 | 95 Nm | ||
| 3AZ Clamping ring for slide after installation in the car | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | 10 Nm | ||
| E30/Allrad | 22 Nm |