2611 Propeller Shaft complete (4AZ To 9AZ)
WARNING: This page does not describe the selected car, but rather 11 other vehicles, including the 2013 BMW 328xi, 2012 BMW 328xi, 2011 BMW 328xi, 2010 BMW 335xi, and 2010 BMW 328xi. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT COMPLETE
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 4AZ | Propeller shaft to drive flange (rear axle final drive) | ||||
| Ausfuhrung Kreuzgelenk: > Quetschmutter |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | Nur Rippmuttern mit hoherem Anziehdrehmoment verbauen |
64 Nm | |
| Ausfuhrung Kreuzgelenk: > Torxschraube |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | 85 Nm | ||
| Ausfuhrung Gleichlaufgelenk: > Torxschraube |
E46 (M3)/E38/E39/E46/E60/E83(M57TU)E63 (N52) | M10 | 70 Nm | ||
| Ausfuhrung Gleichlaufgelenk: > Quetschmutter |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M8 | 32 Nm | ||
| Quetschmutter | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | 64 Nm | ||
| Rippmutter | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M8 | 43 Nm | ||
| Rippmutter | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | 70 Nm | ||
| ZNS Schrauben und Muttern, Zinkuberzug glanzend Alle Ausfuhrungen mit Kreuz. Bzw. Gleichlaufgelenk |
Schrauben und Muttern erneuern Fugemoment und Drehwinkel mussen zwingend eingehalten werden | ||||
| E83/E85/E86/E87/E90/E91/E92/E93/E81/E82/E88 | M10-10.9 Schraube mit Rippverzahnung |
Fugemoment | 40 Nm | ||
| Drehwinkel | 45° | ||||
| E92 M3 | M10 Schraube mit Rippverzahnung |
Fugemoment | 20 Nm | ||
| Drehwinkel | 90 ° | ||||
| E46/E60/E61/E63/E64/E65/E66/E83/E85/E86/E81/E82/E87/E90/E91/E92/E93/E88/E84 | M10-10.9 | Fugemoment | 20 Nm | ||
| Drehwinkel | 90° | ||||
| E90/E91/E92/E93/E81/E87/E82/E83/E88/E84 | M12x55-10.9 | Fugemoment | 55 Nm | ||
| Drehwinkel | 90° | ||||
| Schraube mit Rippverzahnung | E85/M, E86/M | M10x46-10.9 | Schrauben und Unterlegscheiben erneuern | 70 Nm | |
| 5AZ | Pivot fork piece to centre propeller shaft bearing journal with Loctite (Version without sliding piece) |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | 97 Nm | ||
| 6AZ | Centre mount to body | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92/E93/E70/E71/E72/E81/E82/E84/E88/E89 | 21 Nm | ||
| 7AZ | Flexible disc to front axle differential | E53 | M10-10.9 | 60 Nm | |
| 8AZ | Flexible disc on propeller shaft | E53 | M10-10.9 | 64 Nm | |
| 9AZ | Front propeller shaft to transfer box/front axle differential ZNS screws and nuts, shiny zinc coating |
Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | |||
| E60/E61/E90/E91/E92/E84/E70/E71 | M8 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10-10.9 | Jointing torque | 20 Nm | ||
| Angle of rotation | 45° | ||||
| E53/E70/E71/E72 | M10-12.9 | Jointing torque | 10 Nm | ||
| Angle of rotation | 45° | ||||
| E46 | M10x1.5 10.9 | Jointing torque | 5 Nm | ||
| Angle of rotation | 90 ° | ||||
| Universal joint | E70/E71/E72/E83 | M10-10.9 | Jointing torque | 40 Nm | |
| Angle of rotation | 45° | ||||