33 32 Handlebars and struts
WARNING: This page does not describe the selected car, but rather 31 other vehicles, including the 2015 BMW Alpina B7L, 2015 BMW Alpina B7, 2015 BMW 750i, 2015 BMW 750Li, and 2015 BMW 740i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - HANDLEBARS AND STRUTS
| Type | Thread | Tightening specifications | Dimension | ||
|---|---|---|---|---|---|
| 1AZ | Swinging arm/crossmember to rear axle support, front | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 2AZ | Swinging arm to rear axle support, rear | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . . |
|||
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 3AZ | Swinging arm to wheel carrier, rear | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M16 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
265 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 360 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 4AZ | Swinging arm/integral link | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. | |
| Jointing torque | 165 Nm | ||||
| Angle of rotation | 45 ° | ||||
| F03 | M16 | Replace screw and nut. | 250 Nm | ||
| 5AZ | Integral link to wheel carrier | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M12 | 108 Nm | |
| F03 | M16 | 250 Nm | |||
| 6AZ | Toe arm to bearing support/to Integral Active Steering | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M12 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 100 Nm | ||||
| Angle of rotation | 90 ° | ||||
| F03 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 125 Nm | ||||
| Angle of rotation | 90 ° | ||||
| 7AZ | Toe arm to wheel carrier | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. | 165 Nm |
| F03 | M14 | 110 Nm | |||
| 8AZ | Wishbone to rear axle support | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
175 Nm |
| F03 | M18 | Replace nut. TIGHTEN DOWN IN NORMAL POSITION . |
280 Nm | ||
| 9AZ | Wishbone to wheel carrier | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|
| Jointing torque | 90 Nm | ||||
| Angle of rotation | 180 ° | ||||
| F03 | M18 | Replace screw and nut. TIGHTEN DOWN IN NORMAL POSITION . |
|||
| Jointing torque | 200 Nm | ||||
| Angle of rotation | 180 ° | ||||
| 10AZ | Heat shield to toe arm | F01/F02 | M5 | Replace nut. | 6.8 Nm |
| 11AZ | Toe link bearing bracket to rear axle support | F01/F02/F04/F07/F10/F11/F12/F13/F18 | M14 | Replace screws and nuts. | 165 Nm |