64 52 A/C compressor
WARNING: This page is about a different car, the 2010 BMW M3, 2009 BMW M3, and 2008 BMW M3. However, it is still accessible from the selected car via links, so may be relevant.
A/C COMPRESSOR-TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specification | Measure | ||
|---|---|---|---|---|---|
| 1AZ | Refrigerant lines to A/C compressor | E36/7 M54, E36/7 S54, E38, E39, E46, E52, E53, E60, E61, E63, E64, E65, E66, E67, E83, E85, E87, E90, E91, E92, E93 | M8 | 20 Nm | |
| 2AZ | Filler plug, A/C compressor | E36, E38, E39, E46, E52, E53, E60, E61, E63, E64, E65, E66, E67, E83, E85, E87, E90, E91, E92, E93 | 30±1 Nm | ||
| 3AZ | A/C compressor to carrier | M67TU, M54, N62, S85, N54 | M8 | 21 Nm | |
| N45, N46, M47T2, M57TU, M57T2 | M8 | 19 Nm | |||
| N52K | M8 x 87 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 180±15° | ||||
| N52K | M8 x 52 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 90±15 ° | ||||
| N52 | M8 x 87 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 180±15 ° | ||||
| N53 | M8 x 52 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 90±15 ° | ||||
| N53 | M8 x 87 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 180±15 ° | ||||
| E85 S54, E86 S54 | 20 Nm | ||||
| 4AZ | Belt pulley/hub to A/C compressor | M47T2 | 35±5 Nm | ||
| 5AZ | Bracket, A/C compressor to lower crankcase | N54 | 19 Nm | ||
| 6AZ | Cable holder to A/C compressor | M47T2 | 3 Nm | ||
A/C COMPRESSOR-TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specification | Measure | ||
|---|---|---|---|---|---|
| 1AZ | Refrigerant lines to A/C compressor | E70, E71 | M8 | 21 Nm | |
| E60/N47, E61/N47, E81, E82, E87, E88, E90/N47, E91/N47, E92/N47 | M8 | 18.5 Nm | |||
| E92/S65 | M8 | 21 Nm | |||
| 2AZ | Filler plug, A/C compressor | E70, E71 | 30±1 Nm | ||
| E81/N43, E82, E88 | 25 Nm | ||||
| 3AZ | A/C compressor to carrier | E70 | M8 x 15 | 20 Nm | |
| N52, N52K | M8 x 87 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 180±15 ° | ||||
| N52, N52K | M8 x 52 | Replace aluminium screw/bolt | |||
| Jointing torque | 10 Nm | ||||
| Torque angle | 90±15 ° | ||||
| E81/N43, E88 | 23 Nm | ||||
| E82/N47, E90/N47, E91/N47, E92/N47 | 19 Nm | ||||
| E71/N54 | M8 x 85 | 19 Nm | |||
| E71/M57 | M8 x 85 | 19 Nm | |||
| E71/N63 | M8 x 95 | 21.4 ±3.2 Nm | |||
| E71/N63 | M8 x 55 | 19 Nm | |||
| 4AZ | Bracket, pressure line, to compressor | E82/N54 | 7.6 Nm | ||
| 5AZ | Bearing block, compressor, to crankcase | E70/E71 | 19 Nm | ||