37 14 Electric Components
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 BMW 535xi, 2010 BMW 535i, 2009 BMW 535xi, 2009 BMW 535i, and 2008 BMW 535xi. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUES SPECIFICATION (ELECTRIC COMPONENTS)
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1 AZ Wheel camber warning switch to console | E32, E34 | 9 Nm | ||
| 2AZ Angled joint of jointed rod | E32, E34 | 5 Nm | ||
| 3AZ Hydraulic switch to distributor | E24, E32 | 25 Nm | ||
| 4AZ Hydraulic switch to hydraulic control unit | E24, E32 | 27 Nm | ||
| 5AZ Solenoid valve to hydraulic control unit | E24, E32 | 55 Nm | ||
| 6AZ Ride level sensor to holder | E39, E38, E46, E53, E52, E60, E61, E63, E64, E65, E66, E67, E83, E85, E86 | 5 Nm | ||
| 7AZ Control rod/jointed rod to ride height sensor / bracket / control arm | E39, E46 | 9 Nm | ||
| E53, E60, E61, E63, E64, E65, E66, E67, E83, E85, E86 | 8 Nm | |||
| E38 | 5 Nm | |||
| E52 | 10 Nm | |||
| 8AZ Bracket ride level sensor to front axle carrier | E85, E86 | M6 | 8 Nm | |
| 9AZ Control rod on transverse link (rear) | E38, E83 | 8 Nm | ||
| E52 | 10 Nm | |||
| 10AZ Control rod to swinging arm (rear) | E53, E60, E61, E63, E64, E65, E66 | 8 Nm | ||
| 11 AZ Bracket ride level sensor to rear axle carrier | E53, E60, E61, E63, E64, E65, E66, E83, E85, E86 | 8 Nm | ||
| 12AZ Control lines for oscillating motor, rear, to valve block | E60, E61, E63, E64, E65, E66 | 35 Nm | ||
| 13AZ Connecting nuts, hydraulic lines (pressure lines/control lines) | E60, E61, E63, E64, E65, E66 | 30 Nm | ||
| 14AZ Line holder / pipe holder / holder | E60, E61, E63, E64, E65, E66 | 8 Nm | ||
| 15AZ Control lines for oscillating motor, front, to valve block | E60, E61, E63, E64, E65, E66 | 35 Nm | ||
| 16AZ Pressure line DYNAMIC DRIVE circuit to valve block | E60, E61, E63, E64, E65, E66 | 35 Nm | ||
| 17AZ Valve block to holder | E60, E61, E63, E64, E65, E66 | 8 Nm | ||
| 18AZ Control lines to oscillating motor | E60, E61, E63, E64, E65, E66 | 30 Nm | ||
| 19AZ Return line to valve block | E60, E61, E63, E64, E65, E66 | 40 Nm | ||
| 20AZ Holder, valve block, to body | E60, E61, E63, E64, E65, E66 | 8 Nm | ||
| 21AZ Connecting nuts, hydraulic lines (return) | E60, E61, E63, E64, E65, E66 | 35 Nm | ||
| 22AZ Bracket for jointed rod to front control arm | E85, E86 | M6 | 8 Nm | |
| 23AZ Transversal acceleration sensor to body | E60, E61, E63, E64, E65, E66 | M6 | 8 Nm | |
| 24AZ DYNAMIC DRIVE control unit to body | E60, E61, E63, E64 | M8 | 2.5 Nm | |
| E65, E66 | M6 | 4.5 Nm | ||
| 25AZ Mounted acceleration sensor to bracket | E65, E66, E67 | M6 | 8 Nm |