32 31 Steering Column
WARNING: This page is about a different car, the 2010 BMW 535i, 2009 BMW 535i, and 2008 BMW 535i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUES SPECIFICATION (STEERING COLUMN)
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Universal joint/coupling to steering gear/steering spindle | E12, E24 / until 5.82 | Replace clamping screw | 25 Nm | |
| E21, E23, E24 / from 5.82, E28, E30, E31, E32, E34, E46, E52, E60, E61, E63, E64, E65, E66, E67, E83 | Recut thread Replace clamping screw |
22 Nm | ||
| E36, E38, E39 | Recut thread Replace clamping screw |
19 Nm | ||
| E53 / Steel joint | M8 10.9 | Recut thread Replace clamping screw |
24 Nm | |
| E53 / Aluminium joint | M8 10.9 | Recut thread. Replace clamping screw |
28 Nm | |
| E85, E86 | M8 | Recut thread Replace clamping screw |
30 Nm | |
| 2AZ Bearing block for steering column adjustment to instrument panel carrier and pedal bearing block | E31, E32, E34 | M8 | 22 Nm | |
| 3AZ Hexagon screw to bearing block for steering column adjustment | E12, E24 / until 5.82 | M10 x 115 | 25 Nm | |
| E28, E24 / from 5.82 | M8 x 110 | 22 Nm | ||
| E23 | M10 x 170 | 27 Nm | ||
| E31, E32, E34 | Observe repair instruction. | |||
| E38, E39, E53 | M8 | Adjustment lever in clamped position | 3.0 Nm | |
| E46, E83 | M8 | Value 1 | 4.0 Nm | |
| Value 2 | 4.8 Nm | |||
| E85, E86 | M8 | Adjusting lever without needle bearing | 6 Nm | |
| Adjusting lever with needle bearing | 3.2 Nm | |||
| 4AZ Clamp/shackle for outer steering tube | E12, E21, E24, E28 | 22 Nm | ||
| E23 | 10 Nm | |||
| 5AZ Airbag: Steering column to holder | E23, E24, E28 | 18 Nm | ||
| 6AZ Steering column to instrument panel / support tube | E60, E61, E63, E64, E65, E66, E67, E83, E85, E86 | 21 Nm | ||
| 7AZ Steering column to dashboard | E12, E23, E24, E28 | 14 Nm | ||
| 8AZ Sliding piece (screw/nut) | E46 | 9.5 Nm | ||
| 9AZ Control unit, steering column (CIM) to steering column | E65, E66, E67 | 2.5 Nm | ||
| 10AZ Bracket for sleeve to body | E85, E86 | M6 | 2.4 Nm | |
| E83 | M6 | 2.8 Nm | ||
| 11AZ Cable holder to steering column | E46 | M5 (silver) | 8.8 Nm | |
| E46 | M5 (black) | 4 Nm | ||
| 12AZ Electric drive to steering column | E65, E66 | M6 | 8 Nm | |
| E60, E61, E63, E64 | 6 Nm | |||
| 13AZ Steering spindle to double universal joint / universal joint | E53, E65, E66, E67, E83 | Recut thread Replace clamping screw |
28 Nm | |
| 14AZ Universal joint with corrugated tube to steering gear | E65, E66, E67 | Recut thread Replace clamping screw |
22 Nm | |
| 15AZ Bearing block of steering column to bulkhead | E83 | M8 | Replace nuts | 21.4 Nm |
| 16AZ Steering column to bearing block | E83 | M6 | Stick in nut again | 8.8 Nm |
| 17AZ Steering spindle middle section to assembly partition wall | E60 / Four Wheel Drive, E61 / Four Wheel Drive | 6 Nm |