LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2010 >> Milan Base, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1500 (Engine Controls - Pinpoint Test A: No Start Through Pinpoint Test DK: Accelerator Pedal Position (App) Sensor - (Except Diesel & Hybrid)) >> PINPOINT TEST DJ: Air Conditioning Evaporator Temperature (ACET) Sensor >> Test Procedure

Test Procedure

WARNING: This page does not describe the selected car, but rather 31 other vehicles, including the 2008 Mercury Sable, 2008 Mercury Mountaineer, 2008 Mercury Milan, 2008 Mercury Mariner, and 2008 Mercury Grand Marquis. However, it is still accessible from the selected car via links, so may be relevant.
  1. DJ1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) 
    • Are DTCs P0537, P0538, P1436, or P1437 present? 
    Yes No
    For KOEO and KOER DTCs P0538 or P1437, GO to  DJ2.
    For KOEO and KOER DTCs P0537 or P1436, GO to  DJ6.
    For continuous memory DTCs P0537, P0538, P1436 or P1437, GO to  DJ9.    		 For all others, GO toDIAGNOSTIC TROUBLE CODE (DTC) CHARTS AND DESCRIPTIONS .
  2. DJ2 KOEO AND KOER DTCS P0538 OR P1437: SIMULATE AN OPPOSITE SIGNAL TO THE PCM 
    • ACET Sensor connector disconnected.
    • Connect a 5 amp fused jumper wire between the following:
      Point A ACET Sensor Connector, Harness Side Point B ACET Sensor Connector, Harness Side
      ACET - Pin 2 SIGRTN - Pin 1
    • Check for self-test DTCs.
    • Are DTCs P0537 or P1436 present? 
    Yes No
    INSTALL a new ACET sensor. CLEAR the DTCs. REPEAT the self-test. GO to  DJ3.
  3. DJ3 CHECK THE ACET AND SIGRTN CIRCUIT FOR AN OPEN IN THE HARNESS 
    • Key in OFF position.
    • Remove the jumper wire(s).
    • PCM connector disconnected.
    • Measure the resistance between:
      ( + ) ACET Sensor Connector, Harness Side ( - ) PCM Connector, Harness Side
      ACET - Pin 2 ACET - Pin B53
      SIGRTN - Pin 1 SIGRTN - Pin B58, E58
    • Are the resistances less than 5 ohms? 
    Yes No
    GO to  DJ4. REPAIR the open circuit. CLEAR the DTCs. REPEAT the self-test.
  4. DJ4 CHECK THE ACET CIRCUIT FOR A SHORT TO VOLTAGE IN THE HARNESS 
    • Key ON, engine OFF.
    • Measure the voltage between:
      ( + ) ACET Sensor Connector, Harness Side ( - )
      ACET - Pin 2 Ground
    • Is the voltage less than 1 V? 
    Yes No
    GO to  DJ5. REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
  5. DJ5 CHECK THE ACET CIRCUIT FOR A SHORT TO VREF IN THE HARNESS 
    • Key in OFF position.
    • Measure the resistance between:
      ( + ) PCM Connector, Harness Side ( - ) PCM Connector, Harness Side
      ACET - Pin B53 VREF - Pin E57
    • Is the resistance greater than 10K ohms? 
    Yes No
    GO to  DJ10. REPAIR the short circuit. CLEAR the DTCs. REPEAT the self-test.
  6. DJ6 KOEO AND KOER DTCS P0537 OR P1436: SIMULATE AN OPPOSITE SIGNAL TO THE PCM 
    • ACET Sensor connector disconnected.
    • Carry out the KOEO self-test.
    • Are DTCs P0538 or P1437 present? 
    Yes No
    INSTALL a new ACET sensor. CLEAR the DTCs. REPEAT the self-test. GO to  DJ7.
  7. DJ7 CHECK THE ACET CIRCUIT(S) FOR A SHORT TO SIGRTN IN THE HARNESS 
    • Key in OFF position.
    • PCM connector disconnected.
    • Measure the resistance between:
      ( + ) ACET Sensor Connector, Harness Side ( - ) ACET Sensor Connector, Harness Side
      ACET - Pin 2 SIGRTN - Pin 1
    • Is the resistance greater than 10K ohms? 
    Yes No
    GO to  DJ8. REPAIR the short circuit. CLEAR the DTCs. REPEAT the self-test.
  8. DJ8 CHECK THE ACET CIRCUIT(S) FOR A SHORT TO GROUND IN THE HARNESS 
    • Measure the resistance between:
      ( + ) ACET Sensor Connector, Harness Side ( - )
      ACET - Pin 2 Ground
    • Is the resistance greater than 10K ohms? 
    Yes No
    GO to  DJ10. REPAIR the short circuit. CLEAR the DTCs. REPEAT the self-test.
  9. DJ9 CONTINUOUS MEMORY DTCS P0537, P0538, P1436 OR P1437: CHECK THE ACET AND SIGRTN CIRCUIT FOR AN INTERMITTENT CONCERN 
    NOTE: The voltage should be between 4.5 and 5.5 volts. The voltage reading changes suddenly when a concern is detected. For P0537/P1436, a sudden change could indicate a short to ground. For P0538/P1436, a sudden change could indicate an open ACET or SIGRTN circuit.
    • ACET Sensor connector disconnected.
    • Inspect the connectors for signs of damage, water intrusion, or corrosion.
    • Measure the voltage between:
      ( + ) ACET Sensor Connector, Harness Side ( - ) ACET Sensor Connector, Harness Side
      ACET - Pin 2 SIGRTN - Pin 1
    • Key ON, engine OFF.
    • While monitoring the voltage reading on the digital multimeter (DMM), wiggle, shake, and bend small sections of the wiring harness while working from the sensor to the PCM.
    • Key in OFF position.
    • Is there any change in the voltage reading, or is a concern found? 
    Yes No
    ISOLATE the concern. REPAIR as necessary.
    CLEAR the DTCs. REPEAT the self-test.    		 Unable to duplicate or identify the concern at this time.
    refer to PINPOINT TEST Z .
  10. DJ10 CHECK FOR CORRECT PCM OPERATION 
    • Disconnect all the PCM connectors.
    • Visually inspect for:
      • pushed out pins.
      • corrosion.
    • Connect all the PCM connectors and make sure they seat correctly.
    • Carry out the PCM self-test and verify the concern is still present.
    • Is the concern still present? 
    Yes No
    INSTALL a new PCM.
    REFER toFLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM) , Programming the VID Block for a Replacement PCM.    		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
scientia non olet · About LEMON Manuals