LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2009 >> Mariner Base, 2.5 7, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Automatic Transmission) >> General Procedures >> Transmission Fluid Drain and Refill - Without Torque Converter Drain Plug >> Filling

Transmission Fluid Drain and Refill - Without Torque Converter Drain Plug: Filling

WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the fluid drain plug.
    • Tighten to 26 Nm (19 lb-ft).
    2. Fig 1: Identifying Fluid Drain Plug
    G03948593Courtesy of FORD MOTOR CO.
  2. Hold the larger drain plug with a wrench and remove the small (center) fluid level indicating plug.
    3. Fig 2: Identifying Small (Center) Fluid Level Indicating Plug
    G03948559Courtesy of FORD MOTOR CO.
  3. Install the special tool into the pan.
    4. Fig 3: Identifying Special Tool (307-437)
    GF0015442Courtesy of FORD MOTOR CO.
    NOTE: Prior to filling the special tool with clean transmission fluid, make sure that the canister is clean.
  4. Fill the special tool with clean automatic transmission fluid.
    5. Fig 4: Filling Special Tool 307-D465 With Clean Automatic Transmission Fluid
    GF0015445Courtesy of FORD MOTOR CO.
  5. Hang the special tool under the vehicle, upright and close to the transmission.
    6. Fig 5: Hanging Special Tool 307-D465 Under Vehicle
    GF0015446Courtesy of FORD MOTOR CO.
  6. Connect the special tools.
    • Connect the open end of the fluid hose from the Fluid Transporter/Evacuator/Injector to the Adapter, Fluid Level and Fill Plug at the bottom of the transmission fluid pan.
    7. Fig 6: Identifying Special Tools (307-437) And (307-D465)
    GF0015447Courtesy of FORD MOTOR CO.
  7. Apply a maximum of 206.85 kPa (30 psi) to the open end of the vacuum/pressure hose from the special tool. Fluid will immediately start flowing out of the special tool into the transmission fluid pan.
    8. Fig 7: Identifying Special Tools (100-D009) And (307-D465)
    GF0015448Courtesy of FORD MOTOR CO.
  8. Add 2 or 3 quarts of transmission fluid into the fluid pan. Stop the process by releasing the air pressure and removing the air nozzle from the end of the hose.
    9. NOTE: Engine idle speed is approximately 650 RPM.
  9. Start and run the engine until the transmission fluid temperature is between 27°-49°C (80°-120°F).
  10. Inspect the fluid level in the special tool. If the fluid drains back into the canister, the transmission is full. If no fluid drains back, more fluid will need to be added. Repeat Steps 8 and 9.
  11. Once the transmission is full, place a hand vacuum pump on the open end of the vacuum/pressure hose of the special tool and apply vacuum to the system. This will pull out any extra fluid trapped in the system and direct it into the container.
    12. Fig 8: Identifying Special Tools (416-D002) And (307-D465)
    GF0015449Courtesy of FORD MOTOR CO.
  12. Allow the fluid to drain. When the fluid comes out as a thin stream or drip, the fluid is at the correct level.
    13. Fig 9: Allowing Fluid To Drain
    GF0015450Courtesy of FORD MOTOR CO.
  13. Reinstall the small (center) fluid level indicating plug using a 3/16-inch Allen key.
    • Tighten to 10 Nm (89 lb-in).
    14. Fig 10: Identifying Small (Center) Fluid Level Indicating Plug
    G03948559Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals