LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2009 >> Mariner Base, 2.5 7, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 55 (Supplemental Restraint System) >> General Procedures >> Supplemental Restraint System (SRS) Deactivation and Reactivation >> Reactivation

Supplemental Restraint System (SRS) Deactivation and Reactivation: Reactivation

WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove RCM fuse 17 (10A) from the SJB.
  2. Disconnect the battery ground cable and wait at least one minute.
  3. Remove the Restraint System Diagnostic Tool from the vehicle harness side of the driver side air bag module electrical connector.
    4. Fig 1: Attaching Restraint System Diagnostic Tool To Driver Side Air Bag Module Electrical Connector
    GF0014980Courtesy of FORD MOTOR CO.
  4. Connect the driver side air bag module electrical connector and reset the red locking tab.
    5. Fig 2: Locating Driver Side Air Bag Module Electrical Connector
    GF0014979Courtesy of FORD MOTOR CO.
  5. Remove the Restraint System Diagnostic Tool from the vehicle harness side of the passenger side air bag module electrical connector.
    6. Fig 3: Attaching Restraint System Diagnostic Tool To Passenger Side Air Bag Module Electrical Connector
    GF0014978Courtesy of FORD MOTOR CO.
  6. Connect the passenger side air bag module electrical connector and reset the red locking tab.
    7. Fig 4: Locating Passenger Side Air Bag Module Electrical Connector
    GF0014977Courtesy of FORD MOTOR CO.
  7. Remove the Restraint System Diagnostic Tool from the vehicle harness side of the passenger air bag module electrical connector.
    8. Fig 5: Attaching Restraint System Diagnostic Tool To Vehicle Harness Side Of Passenger Air Bag Module Electrical Connector
    GF0014976Courtesy of FORD MOTOR CO.
  8. Connect the passenger air bag module electrical connector.
    9. Fig 6: Locating Passenger Air Bag Module Electrical Connector
    GF0014975Courtesy of FORD MOTOR CO.
  9. Close the glove compartment door.
  10. Remove the Restraint System Diagnostic Tool from the clockspring electrical connectors.
    11. Fig 7: Locating Restraint System Diagnostic Tools
    GF0014974Courtesy of FORD MOTOR CO.
  11. Connect the 2 electrical connectors and position the driver air bag module.
    12. Fig 8: Locating Driver Air Bag Module Electrical Connectors
    GF0014973Courtesy of FORD MOTOR CO.
  12. Install the 2 driver air bag module bolts (1 shown).
    • Tighten to 7 Nm (62 lb-in).
    13. Fig 9: Locating Driver Air Bag Module Bolts
    GF0014972Courtesy of FORD MOTOR CO.
  13. Install the 2 driver air bag module bolt caps (1 shown) in the steering wheel.
    14. Fig 10: Locating Driver Air Bag Module Bolt Caps
    GF0014971Courtesy of FORD MOTOR CO.
    WARNING: Remove restraint system diagnostic tools from the vehicle prior to road testing. If tools are not removed, the supplemental restraint system (SRS) device may not deploy in a crash. Failure to follow this instruction may result in serious personal injury or death in a crash and possibly violate vehicle safety standards.
  14. Make sure all restraint system diagnostic tool(s) that may have been installed during the repair have been removed from the vehicle and all SRS components are connected.
  15. Turn the ignition switch from OFF to ON.
  16. Install RCM fuse 17 (10A) to the SJB and close the cover.
    17. WARNING: Make sure no one is in the vehicle and there is nothing blocking or placed in front of any air bag module when the battery is connected. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
  17. Connect the battery ground cable.
  18. Prove out the SRS as follows:

    Turn the ignition switch from ON to OFF. Wait 10 seconds, then turn the ignition switch back to ON and visually monitor the air bag warning indicator with the air bag modules installed. The air bag warning indicator will light continuously for approximately 6 seconds and then turn off. If an air bag SRS fault is present, the air bag warning indicator will:

    - fail to light.

    - remain lit continuously.

    - flash at a 5Hz rate (RCM not configured).

    The air bag warning indicator might not light until approximately 30 seconds after the ignition switch has been turned from the OFF to the ON position. This is the time required for the RCM to complete the testing of the SRS. If the air bag warning indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5 sets of 5 beeps. If this occurs, the air bag warning indicator and any SRS fault discovered must be diagnosed and repaired.

    Clear all continuous DTCs from the RCM using a scan tool.

scientia non olet · About LEMON Manuals