LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2008 >> Milan Base, 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 660 (Instrument Cluster And Panel Illumination) >> Diagnosis And Testing >> Instrument Cluster and Panel Illumination >> Pinpoint Tests >> Pinpoint Test C: One Or More Module-Controlled Illumination Source(s) Is Inoperative >> Pinpoint Test C: One Or More Module-Controlled Illumination Source(S) Is Inoperative

Pinpoint Test C: One Or More Module-Controlled Illumination Source(S) Is Inoperative

WARNING: This page is about a different car, the 2006 Mercury Milan, 2006 Lincoln Zephyr, and 2006 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
  1. C1 CHECK THE VOLTAGE TO THE SINGLE ILLUMINATION SOURCE 
    • Key in OFF position.
    • Disconnect: Inoperative Illumination Source.
    • With the parking lamps ON, rotate the instrument panel dimmer switch to the full illumination position.
    • Measure the voltage between the inoperative illumination source, harness side and ground as follows:
      CONNECTOR - PIN CIRCUIT

      Component Connector - Pin Circuit
      Floor shifter C3245-3 VLN04 (VT/GY)
      Manual climate control C2357a-2 VLN04 (VT/GY)
      Memory seat switch C503-3 VLN04 (VT/GY)
      Headlamp switch C205-5 VLN04 (VT/GY)
      Clock C2016-2 VLN04 (VT/GY)
      Message center switch C253-1 VLN04 (VT/GY)
      Traction control switch C2355-6 VLN04 (VT/GY)
      Luggage compartment lid release switch C2269-3 VLN04 (VT/GY)
      LH front window control switch C535a-6 VLN04 (VT/GY)
      RH front window control switch C624-1 VLN04 (VT/GY)
      LH rear window control switch C701-4 VLN04 (VT/GY)
      RH rear window control switch C819-4 VLN04 (VT/GY)
      LH door lock control switch C505-2 VLN04 (VT/GY)
      RH door lock control switch C605-2 VLN04 (VT/GY)
    • Is the voltage greater than 10 volts? 

    Yes  : GO to C2.

    No  : REPAIR the circuit in question. TEST the system for normal operation.

  2. C2 CHECK ILLUMINATION SOURCE GROUND CIRCUIT FOR AN OPEN 
    • Key in OFF position.
    • Measure the resistance between the inoperative illumination source, harness side and ground as follows:
      CONNECTOR - PIN CIRCUIT

      Component Connector - Pin Circuit
      Floor shifter C3245-4 GD116 (BK/VT)
      Manual climate control C2357a-1 GD116 (BK/VT)
      Memory seat switch C503-7 GD126 (BK/WH)
      Headlamp switch C205-10 GD116 (BK/VT)
      Clock C2016-5 GD116 (BK/VT)
      Message center switch C253-4 GD116 (BK/VT)
      Traction Control switch C2355-1 GD116 (BK/VT)
      Luggage compartment lid release switch C2269-2 GD116 (BK/VT)
      LH front window control switch C535b-6 GD126 (BK/WH)
      RH front window control switch C624-6 GD139 (BK/YE)
      LH rear window control switch C701-1
      C701-6
      CPW15 (YE)
      CPW16 (BU/OG)
      RH rear window control switch C819-1
      C819-6
      CPW17 (BN/GN)
      CPW18 (GY/VT)
      LH door lock control switch C505- 4 GD126 (BK/WH)
      RH door lock control switch C605-4 GD139 (BK/YE)
    • Is the resistance less than 5 ohms? 

    Yes  : INSTALL a new component in question. TEST the system for normal operation.

    No  : REPAIR the circuit. TEST the system for normal operation.