LEMON Manuals: Even more car manuals for everyone
Home >> Mercury >> 2008 >> Milan Base, 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 466 (Automatic Transmission External Controls - F250-F550 Super Duty) >> Diagnosis And Testing >> External Controls >> Pinpoint Tests >> Pinpoint Test A: The Brake Shift Interlock System Does Not Release/Lock Correctly

Pinpoint Test A: The Brake Shift Interlock System Does Not Release/Lock Correctly

WARNING: This page is about a different car, the 2006 Ford Pickup, 2006 Ford F550 Super Duty, 2006 Ford F450 Super Duty, and 2006 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
  1. A1 TEST THE BRAKE LIGHTS 
    • Apply the brake pedal and view the brake lights.
    • Do the brake lights illuminate? 

    Yes  : GO to  A7.

    No  : GO to A2.

  2. A2 TEST FUSE F2.34 (10A) 
    • Key in OFF position.
    • Check fuse: Fuse F2.34 (10A).
    • Is the resistance 5 ohms or less? 

    Yes  : GO to  A4.

    No  : GO to A3.

  3. A3 TEST CIRCUIT 22 (LB/BK) FOR A SHORT TO GROUND 
    • Disconnect: Brake Pedal Position (BPP) Switch C278.
    • Inspect for damaged or pushed-out pins, corrosion or loose wires. Repair as necessary.
    • Measure the resistance between BPP switch C278-3, circuit 22 (LB/BK), harness side and ground.
      Fig 1: Checking Test Circuit 22 (LB/BK) For Short To Ground
      G04650243Courtesy of FORD MOTOR CO.
    • Is the resistance 10,000 ohms or less? 

    Yes  : SERVICE circuit 22 (LB/BK) for short to ground. TEST the system for normal operation.

    No  : GO to A4.

  4. A4 TEST CIRCUIT 22 (LB/BK) FOR AN OPEN 
    • Measure the resistance between the output side of fuse F2.34 (10A) and BPP switch C278-3, circuit 22 (LB/BK), harness side.
      Fig 2: Checking Test Circuit 22 (LB/BK) For Open
      G04650244Courtesy of FORD MOTOR CO.
    • Is the resistance 5 ohms or less? 

    Yes  : GO to A5.

    No  : SERVICE circuit 22 (LB/BK) for open. TEST the system for normal operation.

  5. A5 TEST THE BPP SWITCH 
    • Measure the resistance between BPP switch pin 2 and pin 3.
      Fig 3: Checking Test BPP Switch
      G04650245Courtesy of FORD MOTOR CO.
    • Is the resistance of the switch greater than 10,000 ohms while OFF and 5 ohms or less while ON? 

    Yes  : GO to A6.

    No  : INSTALL a new BPP switch. TEST the system for normal operation.

  6. A6 TEST CIRCUIT 810 (RD/LG) FOR A SHORT TO GROUND 
    • Disconnect: Brake Shift Interlock Actuator (BSIA) C2008.
    • Inspect for damaged or pushed-out pins, corrosion or loose wires. Repair as necessary.
    • Measure the resistance between BSIA C2008-3, circuit 810 (RD/LG), harness side and ground.
      Fig 4: Checking Test Circuit 810 (RD/LG) For Short To Ground
      G04650246Courtesy of FORD MOTOR CO.
    • Is the resistance 10,000 ohms or less? 

    Yes  : SERVICE circuit 810 (RD/LG) for short to ground. TEST the system for normal operation.

    No  : GO to A7.

  7. A7 TEST CIRCUIT 810 (RD/LG) FOR AN OPEN 
    • Measure the resistance between BSIA C2008-3, circuit 810 (RD/LG), harness side and BPP switch C278-2, circuit 810 (RD/LG), harness side.
      Fig 5: Checking Test Circuit 810 (RD/LG) For Open
      G04650247Courtesy of FORD MOTOR CO.
    • Is the resistance 5 ohms or 1 less? 

    Yes  : GO to A8.

    No  : SERVICE circuit 810 (RD/LG) for open. TEST the system for normal operation.

  8. A8 TEST FOR B+ ON CIRCUIT 295 (LB/PK) 
    • Key in ON position.
    • Measure the voltage between BSIA C2008-1, circuit 295 (LB/PK), harness side and ground.
      Fig 6: Checking Test For B+ On Circuit 295 (LB/PK)
      G04650248Courtesy of FORD MOTOR CO.
    • Is B+ present? 

    Yes  : GO to  A12.

    No  : GO to A9.

  9. A9 TEST FUSE F2.27 (15A) 
    • Key in OFF position.
    • Check fuse: Fuse F2.27 (15A).
    • Is the resistance of fuse 5 ohms or less? 

    Yes  : GO to  A11.

    No  : GO to A10.

  10. A10 TEST CIRCUIT 295 (LB/PK) FOR A SHORT TO GROUND 
    • Measure the resistance between BSIA C2008-1, circuit 295 (LB/PK), harness side and ground
      Fig 7: Checking Test Circuit 295 (LB/PK) For Short To Ground
      G04650249Courtesy of FORD MOTOR CO.
    • Is the resistance 10,000 ohms or less? 

    Yes  : SERVICE circuit 295 (LB/PK) for short to ground. TEST the system for normal operation.

    No  : GO to A11.

  11. A11 TEST CIRCUIT 295 (LB/PK) FOR AN OPEN 
    • Measure the resistance between the output side of the central junction box fuse F2.27 (15A) and BSIA C2008-1, circuit 295 (LB/PK), harness side.
      Fig 8: Checking Test Circuit 295 (LB/PK) For Open
      G04650250Courtesy of FORD MOTOR CO.
    • Is the resistance 5 ohms or less? 

    Yes  : GO to A12.

    No  : SERVICE circuit 295 (LB/PK) for open. TEST the system for normal operation.

  12. A12 TEST CIRCUIT 57 (BK) FOR AN OPEN 
    • Measure the resistance between BSIA C2008-2, circuit 57 (BK), harness side and ground.
      Fig 9: Checking Test Circuit 57 (BK) For Open
      G04650251Courtesy of FORD MOTOR CO.
    • Is the resistance 5 ohms or less? 

    Yes  : INSTALL a new BSIA. TEST the system for normal operation.

    No  : SERVICE circuit 57 (BK) for open. TEST the system for normal operation.

scientia non olet · About LEMON Manuals